Rollerhouses EY25 - User Manual

EY25/8Y16
Type
of tubular
motor
with radio control
system instruction
Operation Item
ltem
Operation
Result Illustration
NOTICE:
a
Install motor
terminal
on the same side
as
power
supply.
o
Terminal
of motor with
"Setting"
key
on the motor should
face
toward you
a
Tighten
brackets
until the
motor is horizontai.
a
Antenna
shali be
as straight
as
possible
with
posirion
far
arvay
from
metal
objects.
Directly contact to
metal
objects is
prohibited:
othenvise. the
receiving distance uill
be influenced
seriously.
a
Please
replace the
battery in
time rvhen the remore
transmitter indicator
does
,=
not shine
or
the
remote-controlljng
distance evidently
become shorter.
o Please
take
out the battery
if the remote transmitter
will not be used for
a long
time.
Remote transm itter
keystroke
sketch
aseiting
Key
x*a-?
)
{',^\, \
\
'(
\N"\
)
I /
Wiring I
Po*.er supply
+.a
--
't+
t-,
ffi
:
/,,
[
'.;
(
l
'-
L_-
Change motor
running
direction
1
Press
"Up"
ker on the
Remote
transmilter
If the
motor
goes
up continuousl)'.
the
user don't need to reveme
running
direction; if the motor goes
dou'n. the
user need to re\/erse
running
direction,
please
follou-up
the
operations.
-'-A
y:
//
t t za;7
,V'
OX
@
erimary
2
Keep
down
"Limit"
key and then
"stop"
key'
When the
motor
gives
out
sounds
"Di-Di-Di" release
both keys
Jhe
motor
running direction has
been
chansed
Set lower
limit
1
Keep down
"limit"
The
moror
gives
out sounds
key for 6 seconds
I
..Oi-Oi-Oi"
I
@'H,ff:ll;
2
Release the
key,r.rhen
the
sounds are
disappeared.
The
motor
will enter into the
starus
of limit
setting
3 Press
"Down"
key
The
motor
should
go
down
continuously
4
When the
motor is
running close to
the
end-point
of lower
limit,
press
"Stop"
key on the remote
transmitter
The motor
stops running
5
Press either
of the
"Up"
or the
"Down"
key
The
motor
runs by step and
step
accurately
adiusts lower
limit
6
Confirm
the setting
by
pressing
the
ooConfirm"
key
The motor gives
out
sounds
Di-Di-Di,
the
setting has completed.

Summary

Important Notices

Motor Wiring and Power

Changing Motor Running Direction

Adjust Motor Direction (Up Key)

If motor goes up continuously, no reversal needed; if down, reverse direction.

Change Motor Direction (Limit + Stop Keys)

Hold Limit & Stop keys. Release when 'Di-Di-Di' sounds for direction change.

Setting the Lower Limit

Initiate Lower Limit Setting

Hold 'Limit' key for 6s until sounds cease; motor enters limit setting mode.

Set Lower Limit (Down Key)

Press 'Down' key for continuous motor movement during lower limit setting.

Stop Motor at Lower Limit

Press 'Stop' key when motor reaches the desired lower limit point.

Fine-Tune Lower Limit

Use 'Up' or 'Down' keys for precise step-by-step adjustment of the lower limit.

Confirm Lower Limit Setting

Press 'Confirm' key to finalize the lower limit setting; motor emits 'Di-Di-Di' sound.

Setting the Upper Limit

Set Upper Limit (Up Key)

Press 'Up' key for continuous motor movement during upper limit setting.

Stop Motor at Upper Limit

Press 'Stop' key when motor reaches the desired upper limit point.

Fine-Tune Upper Limit

Use 'Up' or 'Down' keys for precise step-by-step adjustment of the upper limit.

Confirm Upper Limit Setting

Press 'Confirm' key to finalize the upper limit setting; motor emits 'Di-Di-Di' sound.

Eliminating Original Motor Settings

Reset Motor Settings

Hold 'Setting' key for 8s. Release when 'Di-Di-Di' sounds to eliminate paired remote.

Programming Remote Transmitter and Motor

Pair Remote Transmitter (Setting Key)

Hold 'Setting' key for 3s until long 'Di---Di---Di' sounds.

Confirm Remote Pairing

Press 'Confirm' key on transmitter; motor emits quick 'Di-Di-Di' sounds.

Troubleshooting and FAQ

Technical Data

Installing Roller Motor into Window Shades

Prepare Roller Tube

Check tube dimensions and select correct crown/adapter for motor installation.

Fit Motor into Drive Tube

Align notches, slide motor into tube, mount brackets on both ends.

Motor Rubber Grommet Assembly

Remove Grease Protector

Open split ring, slide off protector ring from motor body.

Fit Drive Adaptor

Use cir-clip to secure drive adaptor in position on the motor.

Wiring Connection

Pairing Remote and Motor

Initiate Pairing (Setting Key)

Hold 'SETTING' button on motor mount until motor beeps.

Complete Pairing (Confirm Key)

Press 'CONFIRM' on transmitter within 10s; motor beeps fast indicating successful pairing.

Checking Blind;Rolling Direction

Verify Direction

Check if blind goes up correctly. If down, direction needs changing.

Change Motor Direction

Hold 'LIMIT' and 'STOP' buttons; motor jogs to indicate direction change.

Setup Bottom Limit

Activate Bottom Limit Setting

Press and hold 'LIMIT' button on primary transmitter; motor beeps fast.

Set Bottom Limit (Down Key)

Press 'DOWN' key for continuous motor movement to set the lower limit.

Stop Motor at Bottom Limit

Press 'STOP' when motor reaches the desired lower limit point.

Fine-Tune Bottom Limit

Use 'DOWN' button for step-by-step adjustment of the lower limit.

Confirm Bottom Limit Setting

Press 'CONFIRM' to finalize; motor beeps fast, indicating setting completion.

Setup Upper Limit

Set Upper Limit (Up Key)

Press 'UP' key for continuous motor movement to set the upper limit.

Stop Motor at Upper Limit

Press 'STOP' when motor reaches the desired upper limit point.

Fine-Tune Upper Limit

Press 'UP' button for step-by-step adjustment of the upper limit.

Confirm Upper Limit Setting

Press 'CONFIRM' to finalize; motor beeps fast, indicating setting completion.

Deleting Original Settings on Motor

Reset Motor Memory

Hold 'SETTING' button on motor mount; motor beeps 3 times then fast.

Measuring Roller Tube Dimensions

Measure Type #1 Tube

Fits roller tube type #1: Inside 3/4", OD 7/8" (approx 22mm).

Measure Type #2 Tube

Fits roller tube type #2: Inside 1", OD 1-1/8" (approx 28mm).

Other 1 Roller Tubes

Use with other 1" tubes if compatible; check rubber grommet for fit.

Rollerhouses EY25 Specifications

General

Brand	Rollerhouses
Model	EY25
Category	Engine
Language	English