Check the fluid level in the windscreen
washer reservoir
and
top-up
if
necessary.
16.
Test:
Road
test the
car
for
satisfactory
performance.
Every 20 000
kilometres
(12 000
mites)
or
12 months whichever
is
the
earlier
•t1.
Air
silencer
and
cleaner: Remove and clean
the
wire
mesh
filter
elemeAt.
• 2. · Automatic gearbox: Check the
fluid
level and
top-up
if
necessary.
• 3.
Battery:
Check the
electrolyte
level;
top-up
with
distilled
water if necessary.
* 4. Brakes: Remove the brake drums
and
inspect
linings
for
wear; renew
lining
if
necessary.
Check
and
if
necessary adjust the rear brakes.
Check the
fluid
level in the brake
reservoir
and
top-up if necessary.
* 5. Brake master
cylinder:
Lubricate
the grease
nipple
on
the master
cylinder
balance
lever.
• t6. Carburetters: Check the oi I I eve I in the
air
valve
dampers
and
if necessary top-up
to
correct
level.
Check
float
chamber depression
and
rectify
if
necessary.
Check the exhaust
co emission;
if
necessary
adjust the carburetter mixture strength
and
idle
speed.
Check
and
if
necessary set the
cold
start
fast-idle
speed.
*t7.
Crankcase breather tube: Remove
and
clean
the
flame
traps in the crankcase breather tube and
also clean the adapter in the choke
butterfly
housing.
*
a.
Engine: Change the engine oi I and
tit
a new
oil
filter
element.
* 9.
Final
drive
unit:
Check the
oil
level
and
top-up
if necessary.
* 10. Front suspension:
Lubricate
the eight grease
nipples
on
the front suspension.
"t11.
Ignition
system:
Fit
new
distributor
contact
breaker
points;
set dwel I angle.
Fit
a new
distributor
cam lubrication
pad
(if
applicable).
If
a
cam
lubrication
pad
is
not
fitted
lightly
smear
the
cam
with
grease.
Lubricate
the
distributor
spindle
(shaft bearings)
and
automatic advance mechanism
with
clean engine
oil.
Fit
new sparking plugs.
Check operation
of
vacuum retard tap
(if
Htted).
Check
ignition
timing with stroboscope and
adjust
if
necessary.
• 12.
Propeller
sh
aft:
Lubricate
the grease n i
pp
I e
in the centre
and
rear universal
joints
and the
sliding
joint.
•
13.
•Steering mechanism: Lubricate the thirteen
grease
nipples
with
the approved grease.
14.
Belts
and
belt
tension: Check the condition
and
tension
of
the
belts
driving
the coolant pump,
steering pump,
and
refrigeration compressor
and
the
alternator,
adjust
or replace
as
necessary.
15.
Brake 1 in kage: Lubricate the brake
Ii
nkage
clevis
and fulcrum pins of the pull rods
and
inter-
mediate
levers.
16. Control I inkages: Apply a
few
drops
of
engine
oil
to the accelerator linkage and
to
the gear range
selector
controls
adjacent to the gearbox casing.
17.
Electrical
system: Ensure that al I lamps,
instruments
and
air
conditioning controls are
operating
satisfactorily.
18. Handbrake I inkage:
Lubricate
the
pivot
pins
and
pulleys
in the handbrake system
with
the
approved grease.
19. Rear fuel
filter:
Remove
the
gauzes
and
clean
them. Drain and clean the
filter
bowl.
20. Servo: Check
and
if
necessary adjust the servo.
21. Shock dampers: Check
for
signs
of
fluid
leaks.;
if apparent inspect the
fluid
level
and
if
necessary
top-up
with
the approved
fluid.
22. Wheels
and
tyres: Check and
if
necessary
adjust the tyre pressures.
Inspect the tread depth
of
al I tyres; al
so
inspect the tyres
for
damage.
Check
and
if
necessary balance the wheels.
23. Check the
following
levels:
Check the
fluid
level in the power steering
pump
reservoir
and top-up
if
necessary.
Check the level and
specific
gravity
of
the
engine coolant
and
correct
if
necessary.
Check the
fluid
level in the windscreen washer
reservoir; top-up
if
necessary.
24.
Test:
Road test the
car
for
satisfactory
performance.
Every 40 000 kilometres
(24
000 miles) or 2 years
whichever
is
the
earlier
In
addition to the
20
000 kilometres (12 000 miles)
service schedule carry out the
following.
In
the case
of
the Automatic gearbox,
Carburetters and the
Final
drive
unit
the
servicing
necessary
is
listed
in
this
schedule therefore the
20
000 kilometres (12 000 miles) service schedule
should
not
be
consulted for these items.
•
+1.
Automatic choke: Check the
flow
through the
choke stove
pipe
and
check
for
correct functioning.
Rectify
if necessary.
* 2. Automatic gearbox: Drain the gearbox and
fluid
coupling;
fill
with
recommended
fluid.
Clean
the
breather
in
the top
of
the
dipstick.
•t3. Carburetters: Clean the
air
valves; top-up the
oi I level in the
air
valve
dampers.
If
paper
filter
elements are
fitted
to
the
float
chamber
lids,
renew the elements.
Check
float
chamber depression
and
rectify
if
necessary.
Check the exhaust
CO
emission;
if
necessary
reset carburetter mixture strength and engine
idle
speed.
Check
and
if
necessary reset the
cold
start
fast-idle
speed.
• 4. Engine cooling system:
Fit
a new engine
coolant
thermostat.
Examine the condition
of
al I hoses;
flt
new
hoses as necessary.
Fit
new heater tap hoses
(irrespective
of
visual
appearance).
• 5.
Final
dr.ive
unit:
Drain the
final
drive
unit
and
fi
11
with
recommended oi
I.
·t6.
Fuel
mixture weakening
device
filter:
Fit
a new
fuel mixture weakening
device
filter.
To Next Page
Loading...
