C
* 3. Engine
cooling
system:
Fit
a new thermostat.
Examine the condition of
all
hoses;
fit
new hoses as
necessary.
Fit
new heater tap hoses
(irrespective
of
visual appearance).
• 4.
Final
drive
unit:
Change the oi I.
·ts. Fuel evaporation emission control system
(1975 model year cars): Renew the
foam
filter
element in the evaporation
loss
control canister.
Check the condition of pipes and connections. Check
the purge rate;
this
should be between 1,41 cu.
m.
per
hr.
and
1,98
cu.
m.
per hr. (50
cu.
ft.
per hr.
and
70 cu.
ft.
per hr.) at 600 r.p.m. in neutral.
Renew the purge
line
filter
if
necessary.
•ts.
Fuel mixture weakening device
filter
(If
fitted):
Fit
a new fuel mixture weakening device
filter.
•
?.
Torque converter transmission
(If
fitted):
Change the transmission
fluid
and
fit
a new
intake
strainer. Renew
'O'
ring
on
intake
pipe
and
fit
a new
seal to bore of
intake
strainer.
8. Dynamo
(If
fitted):
Check the brushes
for
wear
and
freedom in their holders;
fit
new brushes
if
necessary.
9. Fuel
filter:
Clean out the
filter
bowl
and
fit
a new
filter
element.
10.
Fuel pumps: Remove
pumps
and
test
fuel
pump
efficiency;
fit
new pumps
if
necessary.
11. Fuel tank: Release the fuel tank drain plug
and
al low any accumulated water to drain away;
fit
the drain plug
and
add four S.B.N.
inhibitors
to the
tank.
12.
Height
control mechanism: Disconnect, clean
and
lubricate
the height control valve ball
joints;
connect bal I
joints.
13. Power operated hood
(If
fitted):
Check the
level
of
fluid
in
the reservoir; top·up
if
necessary.
14.
Propeller
shaft
(Cars
fitted
with the four speed
automatic gearbox): Examine the neoprene seal at
the front end of
the
shaft
for
servi ceab i
Ii
ty;
rectify
as necessary.
Examine the rear
joint
for signs
of
grease
leakage;
rectify
as necessary.
Check the torque tightness
of
ttie bolts
securing the front and rear
joints;
rectify
as
necessary.
15.
Rear wheel
drive-shafts:
Lubricate
the outer
universal
joints
with
approved grease.
16.
Steering
pump
(Hobourn Eaton): Renew the
filter
element
in
the steering
pump
reservoir.
Every 60 000,kilometres (36 000 miles) or 3
years whichever
is
the
earlier
In
addition
to the 20 000 kilometres (
12
000
mi
I es)
:g
and the 40 000 kilometres (24 000 miles)
service
o,
schedu I es carry
out
the
following.
~
1.
Wax
capsule
type fuel mixture weakening
::E
device
cut·off
valve
(If
fitted):
Fit
the
later
type
thermal
switch
assembly.
ci
"?
I-
Recommended Seasonal Schedules
Every
12
months
1.
Air
conditioning
system: Check that the foam
filter
element
in
the
scuttle
intake
grille
is
free from
obstruction;
fit
a new element
if
necessary.
On
Long
wheelbase cars
fitted
with
a centre
division,
ensure
that the foam
filter
element
fitted
below the rear
refrigeration system
air
intake
grille
is
free from
obstruction.
Fit
a new
filter
element
if
necessary.
Check the refrigeration system for correct
operation,
rectify
as necessary. Any work
on
the
refrigeration system must
only
be
carried
out
by
an
experienced refrigeration engineer.
2. Body drain
holes:
Ensure that the body drain
holes
are not obstructed.
3. Engine cooling system: Drain
off
the old coolant
and fill the system with fresh anti-freeze/water mixture.
Just
prior to the Autumn. clean any debris from the
surfaces
of
the refrigeration condenser and radiator
matrices by reverse flushing with a
hose.
Every 2 years
1. Engine
cooling
system: Carry out the
12
months
service
procedure and
also
thoroughly reverse
f I ush the
cooling
system. Examine cool ant hoses
and
fit
new hoses as necessary.
Service Recommendations
It
is
emphasised
that
these
service
recommendations
are not normal
servicing
arrangements and should
only
be carried out at the request
of
the Owner.
Every 80 000 kilometres (48 000
miles)
1.
Brake and
hydraulic
systems:
Fit
new front
and
rear accumulator to frame hoses. Examine the
condition of the sub-frame to brake
caliper
hoses;
fit
new hoses where necessary. Drain
off
the
hydraulic
fluid;
clean out the
hydraulic
fluid
reservoirs and clean
sight
glasses.
Fi
11
the systems
with
fresh Castrol RR
363
Brake
Fluid
and bleed
the systems.
Every 160 000 kilometres (96 000 miles)
1,
Brake
and
hydraulic
systems:
Fit
all
new
flexible
hoses to the brake and
hydraulic
systems.
Fit
new seals to the
disc
brake
calipers
and the
deceleration
conscious
pressure I
imiting
valve
Drain
off
the
hydraulic
fluid;
clean out the
hydraulic
fluid
reservoirs and clean the
sight
glasses.
Fill
the
systems with fresh Castrol RR 363 Brake
Fluid
and
bleed the systems.
2. Fuel system:
Fit
a new convoluted hose between
the
fi
Iler
head
and
the fuel tank. Examine al I
flexible
fuel pipes; renew any that show signs of
deterioration.
E3 - 3
To Next Page
Loading...
