Ensure tightness of float chamber covers
is
correct.
Check
float
chamber depression and
rectify
if
necessary.
Check engine
idle
speed
and
choke
idle
speed; adjust as necessary.
• t
4.
Crankcase emission control system: Remove
and clean the gauze flame traps in the crankcase
breather tube. Clean the adapter
in
the choke
butterfly
housing.
• t
5.
Engine: Change the engine
oil
and
fit
a new
oi
I
fi
I ter element.
6.
Fuel evaporation emission control system:
Check
the
condition
of
the
pipes
and
connections.
• t
7.
Ignition
system:
Fit
new sparking plugs
ensuring that the gaps are set
to
0.035
in.
Lubricate
distributor
spindle
(shaft
bearings)
and
automatic advance mechanism with engine
oil.
Check the ignition timing using stroboscope
and
adjust
if
necessary; the
ignition
ti
ming should
be
15
B.
T.D.C.
with the engine running at 1 200
r.p.m.
•
8.
Battery: Check the
electrolyte
level;
top-up
with
distilled
water if necessary.
*
9.
Brakes: Inspect footbrake and parking brake
pad
linings,
fit
new pads
if
necessary.
When
renewing
footbrake pads examine condition of dust excluders
on
calipers
and renew
if
necessary.
Manually adjust the parking brake
caliper
mechanism.
Inspect
all
pipes
and
connections. ReRort
any
defects
to
the Owner.
• 10.
Final
drive
unit:
Check the
oil
level
and
top-up
if
necessary.
• 11. Front suspension: Inspect the front suspension
bal I
joint
rubber covers;
if
the covers are damaged.
fit
new
joints
and covers.
• 12. Steering mechanism:
Lubricate
the steering
mechanism
at
the
six
grease points. Inspect the
rubber covers
on
the bal I
joints;
if
the covers are
damaged the
joints
should
be
dismantled and new
parts
fitted
as necessary •.
• 13. Torque converter transmission: Change the
transmission
fluid.
When
checking the
fluid
level
avoid
contact
with
the exhaust gas recirculation
valve
and
associated pipes as these contain
hot exhaust gases.
18
500 miles
or
18
months
whichever
is
the
earlier
Carry out the 6 000 miles
or
6 months
Essential
Maintenance schedule.
25
000 miles or 2 years whichever
is
the
earlier
In addition
to
the
12
500
miles
or
12
months
Essential
maintenance schedule, carry out the
following.
· In the case of Carburetters, Fuel evaporation
emission control system, Final
drive
unit
and the
Torque converter transmission the
servicing
necessary
is
listed
in
this
schedule therefore the
12
500
miles
service
schedule should not
be
consulted for these items.
E5 - 2
· t1.
Air
injection system:· Check the
air
injection
system for leaks
and
correct functioning. Renew any
defective items.
• t 2. Automatic choke: Check the
flow
through the
choke stove pipe
and
check for correct functioning.
Rectify
if
necessary.
• t 3. Carburetters: Clean
air
valves.
Remove
inlet
unions from the
float
chamber
covers
and
fit
new paper
filter
elements:
Top-up oi I level in
air
valve
dampers.
Ensure tightness
of
float
chamber covers
is
correct.
Check
float
chamber depression and rectiry
if necessary.
Check engine
idle
speed and choke
idle
speed; adjust as necessary.
• t 4. Carburetter mixture weakening device:
Fit
a
new
air
filter
element
for
the carburetter mixture
weakening device.
• t
5.
Fuel evappration emission control system:
Fit
a new
foam
filter
element in the evaporation
loss
control canister.
Check the purge rate;
this
should
be
between
50
cu.
ft.
per hr.
and
70 cu.
ft.
per
hr.
at 600 r.p.m.
in neutral.
Fit
a new purge I ine
filter
if
necessary.
Check the condition
of
pipes
and
connections.
•
6.
Engine cooling system:
Fit
a new engine
coolant thermostat
and
heater tap feed hose.
•
7.
Final
drive
unit:
Change the
oil.
8.
Torque converter transmission: Change the
transmission
fluid
and
fit
a new
intake
strainer.
Renew
·o·
ring
on
intake pipe and
fit
a new seal
to
bore
of
intake strainer.
When
checking the
fluid
level avoid contact
with
the exhaust gas
recirculation
valve
and
associated pipes as these contain
hot exhaust
gases.
31
000
miles
or
2Y1
years
whichever
is
the
earlier
Carry out the 6 000 miles
or
6 months
Essential
Maintenance schedule.
37
500
miles
or 3 years whichever
is
the
earlier
Carry out the
12
500 miles
or
12 months
Essential
Maintenance schedule.
43 500
miles
or
3Y2
years whichever
is
the
earlier
Carry out the 6 000 miles
or
6 months
Essential
Maintenance schedule.
50 000
miles
or 4 years whichever
is
the
earlier
In addition to the
25
000
miles
or
2 years
Essential
Maintenance schedule, carry out the
following.
•
t'1.
Exhausl gas
recirculation
system: Remove
and clean the exhaust gas
recirculation
valves
and
feed pipes. Clean the
orifices
in the carburetter
'Tee'
piece. Check the exhaust gas
recirculation
valves
for
correct
operation.
•
t2.
Exhaust system:
Fit
a new
catalytic
converter assembly.
To Next Page
Loading...
