'B'
Service Schedule - Every 20 000 kilometres
(12 000 miles)
or
12
months
whichever is the
earlier
·t1.
Air
filter/silencer:
Clean and
oil
the wire
mesh
filter
elements or (dependent upon type
of
filter
fitted),
fit new paper element(s).
•
2.
Battery:
Check the
electrolyte
level;
top-up
with
distilled
water
if
necessary.
* 3. Brakes: Inspect the footbrake
and
handbrake or
parking brake
pad
linings;
fit
new pads
if
necessary.
When
renewing brake pads, examine the
caliper
dust excluders and renew
if
necessary.
Manually adjust the handbrake,/parking brake
caliper
mechanism.
Inspect pipes
and
connections. Report any
defects
to the Owner.
•
t4.
Carburetters: Check the
air
valve
damper oi I
levels;
top-up
if
necessary.
Check
and
adjust the
float
chamber depression.
Check the engine
idle
speed and choke
idle
speed;
adjust
if
necessary.
Ensure exhaust emissions comply
with
E.C. E.
Regu I at ion 15,
if
applicable.
•
5.
Engine: Change engine oi I and
fit
a new oi I
filter.
·ts. Engine breather system: Remove and clean the
gauze flame traps in the crankcase breather tube.
Clean the adapter in the choke
butterfly
housing.
•
7.
Final
drive
unit:
Check the oi I
level;
top-up
if
necessary.
• 8. Front suspension: Inspect the front suspension
ball
joint
rubber covers;
if
the covers are damaged,
fit
new
joints
and
covers.
·+9.
Ignition
system:
Fit
new
distributor
contact
breaker
pointsi
set
dwell
angle.
Fit
a new
distributor
cam
lubrication
pad.
Lubricate
the
distributor
spindle
(shaft
bearings)
and
automatic advance
mechanism with clean engine
oil.
Fit
new sparking plugs.
Check
ignition
timing with stroboscope and
adjust
if
necessary.
• 10. Steering mechanism:
Lubricate
the steering
mechanism at the
six
grease
points.
Inspect the
rubber covers
on
the bal I
joints;
if
the covers are
damaged the
joints
should
be
dismantled and new
parts
fitted
as necessary.
• 11. Torque converter transmission: Change
transmission
fluid.
12.
Belts
and
belt
tension: Check the
condition
and
tension of the coolant pump, steering
pump
and
refrigeration compressor,
and
alternator
driving
belts;
adjust
or
replace as necessary.
13. Control I inkages:
Lubricate
the
accelerator
I inkage
and
the gear range
selector
controls
(adjacent
to
the transmission casing) with engine
oil.
14.
Electrical
system: Check al I
exterior
I amps,
interior
lamps, warning lamps and
devices,
and
instruments
for
correct operation;
rectify
as
necessary.
15. Handbrake or Parking brake I inkage:
Lubricate
the
pivot
pins
and
pulleys
with
approved grease.
16. Spare wheel carrier:
Lubricate
the spare wheel
carrier lowering
bolt
and mechanism.
E6 - 2
17
Levels
and
pressures: Check the
fluid
level
of th€ steering
pump
reservoir; top-up
if
necessary.
Check the
fluid
level of the steering
idler
box damper; top·up
if
necessary.
Check the lev.el
and
specific
gravity
of the
engine coolant; correct
if
necessary.
Check the
fluid
level in the windscreen
washer reservoir and top-up
if
necessary.
Run
the engine
for
four minutes then check
the I eve
Is
of the hydrau Ii c systems reservoirs;
top-up
if
necessary.
Check
and
ad
just
al I tyre pressures; al so
check tyre tread depth
and
condition of tyres.
Report any defects to the Owner.
18.
Test:
Road
test
the car
for
satisfactory
performance.
'C' Service Schedule - Every
40
000 kilometres
(24
000
miles) or 2 years whichever
is
the
earlier
In addition to the 20 000 kilometres (12 000 miles)
service
schedule carry out the fol lowing.
In the case of the Carburetter,
Final
drive
unit
and the Torque converter transmission the servicin::'
necessary
is
listed
in
this
schedule therefore, the
20
000 kilometres (12 000
miles)
service
schedule
shou Id not be consulted for these items.
•t1.
Automatic choke: Check
flow
through the choke
stove pipe and check
for
correct
function;
correct
as necessary.
·t2.
Carburetters: Clean the
air
valve
pistons.
Top-up the
air
valves
with new engine
oil.
Fit
new paper element f i I
ters
to the fl oat
chamber
inlet
connections.
Check
and
adjust
float
chamber depression.
Check engine
idle
speed and choke
idle
speed;
adjust as necessary.
Ensure exhaust emissions comply
with
E.C.E.
Regulation 15,
if
applicable.
•
3.
Engine cooling system:
Fit
a new thermostat.
Examine the condition of
all
hoses;
fit
new hoses
as necessary.
Fit
new heater tap hoses
(irrespective
of
visual
appearance).
• 4.
Final
drive
unit:
Change the oi
I.
·ts. Fuel mixture weakening
device:
Fit
a new fuel
mixture weakening device
filter.
• 6. Torque converter transmission: Change the
transmission
fluid
and
fit
a new
intake
strainer.
Renew
·o·
ring
on
intake
pipe
and
fit
a new seal to
bore
of
intake
strainer.
7, Fuel
filter:
Clean out the
filter
bowl
and
fit
a
new
filter
element.
8. Fuel pumps: Remove pumps and
test
fuel
pump
efficiency;
fit
new pumps
if
necessary.
9. Fuel tank: Release the fuel tank drain
plL1g
and
al low any accumulated water
to
drain away;
fit
the drain
plug
and add
four S.B.N.
inhibitors
to the
tank.
10.
Height control mechanism: Disconnect, clean
and
lubricate
the height control
valve
ball
joints;
connect ball
joints.
11. Rear wheel
drive-shafts:
Lubricate
the outer
uniyersal
joints
with
approved grease.
To Next Page
Loading...
