3. Exhaust system: Check
grass-fire
heat -
shields
for
damage.
Rectify
or
renew
shields
to
ensure that a minimum clearance
of
5
mm
(0.2 m.)
is
maintained between the heatsh
ields
and the
exhaust pipes.
4.
Battery:
Check the
electrolyte
level;
top-up
with
distilled
water
if
necessary.
5.
Belt
tension: Check the tension
of
all
driving
belts.
6.
Brakes: Inspect footbrake
and
handbrake or
parking brake
pad
linings;
fit
new pads
if
necessary.
When
renewing footbrake pads examine
condition
of
dust excluders on
calipers
and renew
if
necessary.
Manually
adjust
the handbrake or parking
brake
caliper
mechanism.
Inspect
all
pipes
and connections.
Rectify
if
necessary.
7.
Fluid
levels:
Check
all
fluid
levels.
B. Torque converter transmission: Check the
fluid
level and top-up
if
necessary.
When
checking the
fluid
I evel avoid contact
with the exhaust gas
recirculation
valve,
heatshield
and
associated pipes as these components
will
be
hot.
Every
20
000 kilometres (
12
000 miles) or 12
months whichever
is
the earlier
1.
Air
conditioning
system: Check the
refrigeration system
for
correct operation.
rectify
as
necessary. Any work must be carried out by
an
experienced engineer.
2.
Air
injection
pump: Check the tension
of
the
pump
pulley
driving
belt.
3.
Air
silencer:
Fit
a new paper
filter
element.
4. Carburetters: Top-up the
air
valve
dampers
with new engine
oil.
Check and
if
necessary adjust float chamber
depression. Check
tightness
of
float
chamber
covers.
Check engine
idle
speed and choke
fast-idle
speed; adjust as necessary.
5. Crankcase emission control system: Remove
and clean the gauze flame traps in the crankcase
breather tube. Clean the adapter in the choke
butterfly
housing.
6. Engine: Change the engine
oil
and fit a new
oil
filter
element.
7. Exhaust system: Check
grass-fire
heatshields
for
damage.
Rectify
or renew
shields
to ensure
that a minimum clearance
of
5
mm
(0.2
in.)
is
maintained between the
heatshields
and the exhaust
pipes.
8. Fuel evaporation emission control system:
Check the
condition
of
the
pipes and connect ions.
9.
Ignition
system:
Fit
new sparking plugs
ensuring that the gaps are set
to
0,9
mm
(0.035
in.).
Lubricate
distributor
spindle
(shaft
bearings)
and
automatic advance mechanism with engine
oil.
Check
ignition
timing with stroboscope
and
adjust
if
necessary:
The
ignition
timing should be
15°
8.
T.D.C.
with
the engine running at 1 600 r.p.m.,
the vacuum capsu I e disconnected and the feed
hose blanked
off.
10.
Battery: Check the
electrolyte
level;
top-up
with
distilled
water
if
necessary.
E9
- 2
11.
Belt
tension: Check the tension
of
all
driving
belts.
12. Brakes: Inspect footbrake and handbrake or
parking brake pad
linings;
fit
new pads
if
necessary.
When
renewing footbrake pads, examine condition
of
dust excluders on
calipers
and renew
if
necessary.
Manually
adjust
the
handbrake or parking brake
caliper
mechanism.
Inspect
all
pipes
and connections,
rectify
if
necessary.
13.
Final
drive
unit:
Check
the
oil
level;
top-up
if
necessary.
14.
Fluid
levels:
Check
all
fluid
levels.
15. Front suspension:
The
front suspension ball
joints
are sealed for
Ii
fe
and no maintenance
is
required
until
renewal
is
necessary or the
ball
joint
rubber covers are damaged. Inspect the rubber
covers on the front suspension bal I
joints;
if
the
covers are damaged,
fit
new
joints
and covers.
16. Steering ball
joints:
Lubricate
the
six
grease
nipples.
Inspect the rubber
covers
on
the
bal I
joints;
if
the covers are found to be damaged the
joints
should be dismantled and new parts
fitted
as
necessary.
17. Torque converter transmission: Renew
transmission
fluid.
When
checking
fluid
level,
avoid
contact with the exhaust gas
recirculation
valve,
heatsh
ield
and associated
pipes
as these
components
will
be hot.
Every
30 000
kilometres
(18 000
miles)
or
18
months
whichever
is
the
earlier
1.
Air
conditioning
system: Check the
refrigeration system
for
correct operation,
rectify
as
necessary. Any work must be
carried
out by
an
experienced engineer.
2. Engine: Change
the
engine
oil
and
fit
a new
oil
filter
element.
3. Exhaust system: Check
grass-fire
heatshields
for
damage.
Rectify
or renew
shields
to ensure
that a minimum clearance of 5
mm
( 0.2
in'.>
is
maintained between the
heatshields
and
the
exhaust pipes.
4.
Battery:
Check the
electrolyte
level;
top-up
with
distilled
water
if
necessary.
5.
Belt
tension: Check the tension of
all
driving
belts.
6. Brakes: Inspect footbrake and handbrake or
parking brake
pad
linings;
fit
new
pads
if
necessary.
When
renewing footbrake pads examine
condition
of
dust
excl
uders on
calipers
and renew
if
necessary.
Manually adjust the handbrake or parking
brake
caliper
mechanism.
Inspect al I
pipes
and connections.
Rectify
if
necessary.
7.
Fluid
levels:
Check al I
fluid
levels.
B.
Torque converter transmission: Check
fluid
level
and top-up
if
necessary.
When
checking the
fluid
level,
avoid
contact
with
the exhaust gas reci rcu I ati
on
valve,
heatshield
and
associated
pipes as these components
wil
I be hot.
To Next Page
Loading...
