• 3. Brakes: Inspect the footbrake and parking brake
pad
linings;
fit
new pads
if
necessary.
When
renewing
brake pads, examine the
caliper
dust excluders and
renew
if
necessary,
Manually
adjust
the parking brake
caliper
mechanism.
Inspect
pipes
and connections. Report any
defects
to the Owner.
• t 4. Carburetters:
SU
carburetters. Check the
air
valve
damper oi I
levels
and
top-up
if
necessary
also,
check and
adjust
the
float
chamber depression.
Regulation
15,
if
applicable.
• 5. Engine: Change engine oi I and
fit
a new
oil
Ii
lter.
•t6.
Engine breather system: Remove and clean the
gauze flame trap
in
the crank-case breather tube,
also- clean the adapter in the choke
butterfly
housing on
SU
carburetters or the breather connection
in
the
air
filter
housing on the Solex carburetter.
•
7.
Final
drive
unit:
Check the
oil
level;
top-up
if
necessary.
•
8.
Front
suspension: Inspect the front suspension
ba
II
joint
rubber covers;
if
the covers are damaged,
fit
new
joints
and covers.
·t9.
Ignition
system: Lubricc1te the
distributor
spindle
(shaft
bec1rings)
and automatic advance
mechanism
with
clean engine
oil.
Fit
new sparking plugs.
t10.
Ignition
timing and
idle
speeds: Check the
ignition
timing
with a stroboscope and
adjust
ii
necessary.
Check engine
idle
speed and
chOke
idle
speed;
adjust
if
necessary. Ensure exhaust
emissions
comply
with
E.C.E.
Regulation
15
if
applicable.
• 11. Steering
ball
joints:
Lubricate
the
steering
bal I
joints
at
the four grease
points.
Inspect the
rubber covers on the
ball
joints;
if
the covers are
damaged the
joints
shou Id be dismantled and new
parts
fitted
as necessary.
• 12. Steering rack and pinion assembly: Inspect the
convoluted neoprene seals on the
raci<
and pinion
unit
and
check
the seal
clips
for
tightness;
if
the
seals
are damaged new seals should be
fitted.
• 13. Torque converter transmission: Change
transmission
fluid.
14.
Belts
and
belt
tension: Check the
condition
and
tension
of the coolant pump.
steering
pump and
refrigeration
compressor and
alternator
driving
belts;
adjust
or replace as necessary.
15. Control I inkages:
Lubricate
the
accelerator
I inkage and the gear range
selector
controls
(adjacent
to
the transmission
casing}
with
engine
oil.
16.
Electrical
system: Check
all
exterior
lamps,
interior
lamps, warning lamps and
devices
and
instrument.s
for
correct operation;
rectify
as
necessary
17.
Parking
brake I inkage:
Lubricate
the
pivot
pins
and
pulleys
with
approved grease.
18. Spare wheel carrier:
Lubricate
the spare wheel
carrier
lowering
bolt
and
mechanism.
19.
Levels
and pressures: Check the
fluid
level
of
the
steering
pump
reservoir; top·up
if
necessary.
Check the level and
specific
gravity
of the
engine coolant; correct
if
necessary.
Check the
fluid
I evel
in
the windscreen washer
reservoir and top-up
if
necessary.
Run the engine for four munutes then check the
E14 - 2
levels
of
the
hydraulic
systems reservoirs; top·up
if
necessary.
Check and
adjust
all
tyre pressures;
also
check
tyre tread depth and condition
of
tyres. Report any
defects to the Owner.
20.
Test:
Road
test
the
car
for
satisfactory
performance.
'C'
Service
Schedule·
Every 40 000 kilometres
(24 000 miles) or 2 years whichever
is
the
earlier.
In addition to the
20
000 kilometres (12
000
miles)
service schedule carry out the fol lowing.
In the case of the Carburetters,
Final
drive
unit,
Torque converter transmission and
Levels
and
pressures,
servicing
necessary
is
listed
in
this
schedule therefore, the 20
000
kilometres
(12
000
miles)
service
schedule should not be consulted
for
these i terns.
·t1.
Automatic choke:
SU
carburetters. Check
flow
through the choke stove
pipes
and check
for
correct
function; correct as necessary.
··t2.
Carburetters:
SU
carburetters. Clean the
air
valve
pistons.
Top-up the
air
valves
with
new engine
oil.
Fit
new paper element
filters
to the fuel
inlet
connections. Check
c1nd
adjust
float
chamber
depression.
Solex Carburetters - Remove and clean the
filter
in the fuel
inlet
connection.
Check engine
idle
speed and choke
idle
speed;
adjust as necessary.
Ensure exhaust emissions comply
with
E.C.E.
Regulation 15,
if
applicable.
• 3. Engine
cooling
system:
Fit
a new thermostat.
Examine the condition
of
all
hoses;
fit
new hoses
as necessary.
Fit
new heater tap feed hose
(irrespective
of
visual
c!Ppearance).
• 4.
Final
drive
unit:
Change the
oil.
·ts. Fuel mixture weakening device:SU carburetters.
Fit
a new fuel mixture weakening
device
filter.
•
6.
Torque converter transmission: Change the
transmission
fluid
and
fit
a new
intake
strainer.
Renew'
o·
ring
on
intake
pipe
and
fit
a new seal to
bore of
intake
strainer.
7.
Fuel
filter:
Clean out the filter. bowl and
fit
a
new
filter
element.
8.
Fuel pumps: Remove pumps and
test
fuel
pump
efficiency;
fit
new pumps
if
necessary.
9.
Fuel tank: Release the fuel tank drain plug and
allow
any accumulated water
to
drain
away;
fit
the
drain plug.
10.
Height
control mechanism:
Disconnect,
clean
and
lubricate
the
height
control
valve
ball
joints;
connect ball
joints.
11.
Propeller
shaft:
Lubricate
the uni versa I
joints
at
ec1ch
end of the
shaft
with
approved grease.
12. Rear wheel
drive-shafts:
Lubricate
the outer
universal
joints
with
approved grease.
13.
Levels
and press..ires: Check the
fluid
level
in
the steering
pump
reservoir; top-up if necessary·.
Check the
level
and
specific
gravity
of the
engine coolant;
correct
if
necessary.
Check the
fluid
level
in
the windscreen washer
reservoir and top-up
if
necessary.
Run
the engine
for
four minutes then check the
fluid
levels
of the
hydraulic
systems reservoirs;
top-up
if
necessary.
Check and
adjust
all
tyre
pressures;
also
check
To Next Page
Loading...
