ROMAN Haven6 H3P - User Manual

Consumer Guarantee
Please make sure the purchaser/end user completes and returns the guarantee card
which is enclosed with this product. Failure to validate the Guarantee will mean only the 1
Year Statutory Guarantee will apply.
Handling
Be aware toughened glass can shatter if not handled correctly. It should not be subjected
to any sharp impact and it is essential to protect the glass by resting it on a soft protective
surface during installation such as cardboard or carpeting. It is recommended to wear PPE at
all times during installation.
Pre-Installation Checks
1. Please take time to read these instructions prior to installing your product, including the Tray Sizes section below.
2. Check you have the correct product, by looking at the labels on the side of the product packaging.
3. Check all the product components and xing kits are in the box - these are listed on the next page.
4. Please check the product for defects or damage, once the installation has commenced we cannot accept responsibility for any
defects or damage.
5. Before you commence any drilling check there are no hidden electrical cables and/or water pipes.
6. No attempt should be made to re-work the toughened safety glass.
7. The installation of the product should be performed by two persons.
8. It is strongly recommended the product is tted on a tiled surface or similar waterproof surface - which are tiled and grouted
before product is installed.
9. It is strongly recommended that the walls the product is going to be installed on are vertical, and the oor/tray is level.
10. Please note that some natural misting may occur when you remove this product from its packaging, due to the addition of the
glass protection pre-coating. If this does occur this can easily be removed with a soft, dry cloth.
Haven6
Pivot Door
H3P#
REV04 - 08.2023
Tray Sizes
Important: You MUST measure your tray before you proceed with installation. Please refer to the adjustment stated in the brochure
or Step 1 of this instruction manual for the adjustment details for Haven6. If your tray exceeds this given value, you may need a
bespoke product. T Your Tray must be larger than the size given for Corner Adjustments.
Refer to Step 1 for a guide on how to measure your tray accurately before proceeding any further - Roman will not be liable if you
begin installation without correctly measuring your tray, to the realisation it doesn’t t.

Summary

Handling Glass Safely

Pre-Installation Checks Overview

Equipment Checklist and Fixing Kits

Step 1: Tray Size Measurement

Step 2: Detailed Pre-Installation Checks

Step 3: Wall Profile Positioning

Step 4: Door and Second Wall Profile Installation

Step 5: Fitting the Enclosure Components

Step 6: Sealing the Enclosure

Trouble Shooting Guide

Product Maintenance and Care

A list of Donts for Cleaning

Key prohibitions for cleaning and product care to avoid damage.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Installation Requirements and Recommendations
5. Maintenance Features
6. Troubleshooting Guide

This document describes the Haven6 Pivot Door (H3P#), a shower enclosure designed for bathroom use.

Function Description

The Haven6 Pivot Door is a shower enclosure that provides a contained showering space. It features a pivot door mechanism for entry and exit. The enclosure is designed to be installed on a shower tray, creating a waterproof showering area.

Important Technical Specifications

• Glass Type: Toughened safety glass.
• Adjustment Range: The enclosure offers +/- 12.5mm of adjustment in each wall profile, allowing for flexibility in installation on non-level walls or trays.
• Tray Widths (Alcove):
  • H3P7CS: 640mm - 690mm
  • H3P76CS: 700mm - 750mm
  • H3P8CS: 740mm - 790mm
  • H3P9CS: 840mm - 890mm
  • H3P10CS: 940mm - 990mm
• Tray Widths (Corner):
  • H3P7CS: 676mm - 726mm
  • H3P76CS: 736mm - 786mm
  • H3P8CS: 776mm - 826mm
  • H3P9CS: 876mm - 926mm
  • H3P10CS: 976mm - 1026mm
• Drill Bit Sizes:
  • Wall Profile Holes: 4.5mm
  • Wall Plugs: 6mm (Masonry Drill Bit)
  • Vertical Frame to Wall Profiles: 2.5mm
• Screw Sizes:
  • Wall Profile to Wall: 40mm screws (with screw bases)
  • Frame to Wall Profiles: 9mm screws (with screw bases)
• Installation Time: Approximately 90 minutes (excluding sealant curing time).
• Safety Standards: Water tested conforming to BS EN 14428.

Usage Features

• Pre-Coated Glass: The glass is pre-coated for protection, which may cause natural misting upon removal from packaging, easily removed with a soft, dry cloth.
• Two-Person Installation: The installation of the product requires two persons for safety and ease of handling, especially when lifting the door assembly.
• Adjustable Frame: The door can be adjusted within the frame to ensure the gap between the top of the door and the horizontal main frame is parallel. This adjustment also ensures the door lifts away from the bottom of the horizontal main frame.
• Magnetic Closure: Features a door magnet and frame magnet to ensure full contact and secure closure of the pivot door.
• Cover Caps: Screw cover caps are provided to conceal fixings for a clean aesthetic.
• Top Caps: The top caps have grooves and can be shortened by snapping off at these points, with a small amount of sealant recommended to keep them in place.

Installation Requirements and Recommendations:

• Tiled and Grouted Area: The installation area (walls and floor/tray) must be fully tiled and grouted before measuring the tray and commencing installation.
• Level Surfaces: Walls should be vertical, and the floor/tray should be level to achieve optimal adjustment and fitment.
• Soft Protective Surface: During handling, the glass should be rested on a soft protective surface (e.g., cardboard, carpeting) to prevent damage.
• Personal Protective Equipment (PPE): Recommended to wear PPE during installation.
• Sealant Application:
  • A bead of bathroom sealant (width of the wall profile) is required between the tiled wall and tray where the wall profile is positioned.
  • The gap between the tray and wall profile must be sealed on the inside.
  • The wall profile must be sealed vertically, both internally and externally, where it meets the tiles.
  • The base of the enclosure must be sealed to the top of the tray from wall to wall on the outside only.
  • Crucially, DO NOT seal the base of the product to the inside, as this can cause leakage.
  • Allow 24 hours for the sealant to fully cure before using the shower.
• No Re-working Glass: Toughened safety glass should not be re-worked.
• Hidden Utilities Check: Before drilling, check for hidden electrical cables and/or water pipes.
• Tray Measurement: It is critical to accurately measure the shower tray before installation, referring to the provided tray size tables. Incorrect measurement may lead to the product not fitting, and the manufacturer will not be liable.
• Wall Fixings: Wall plugs are supplied for brick or block walls. For plasterboard walls, appropriate wall fixings must be purchased separately.
• Spirit Level Use: A spirit level is essential to ensure wall profiles are completely vertical during installation.

Maintenance Features

• General Maintenance: Products are generally maintenance-free.
• Lubrication: Wheel assemblies and other moving parts (like hinges) may require lubrication periodically.
• Cleaning:
  • Clean with a mild detergent diluted in water, then polish with a soft cloth.
  • For hard water areas, use a 50/50 solution of white vinegar and water. Apply for approximately 5 minutes, then rinse with warm water to remove limescale residue.
  • A quality silicone spray is recommended.
• Cleaning Restrictions (Dont's):
  • Do not use acidic-based products unsuitable for cleaning enamel surfaces.
  • Do not use abrasive cleaners, cleaners with bleach or solvents, as these will adversely affect aluminium profiles.
  • Do not use scouring pads, powder, or any sharp instruments when cleaning the enclosure.

Troubleshooting Guide:

The manual includes a troubleshooting guide for common issues such as leaking, enclosure alignment on the tray, door not operating correctly, and glass door alignment, offering solutions like checking sealant application, ensuring level surfaces, verifying vertical wall profiles, and adjusting door magnets or pivot points.

ROMAN Haven6 H3P Specifications

General

Brand	ROMAN
Model	Haven6 H3P
Category	Bathroom Fixtures
Language	English