5. Temperature settings
To change the temperature settings, press the
[
SET
]
key for 5 seconds.
A: In the first stage, using the arrow keys
[
+
]
, you can choose between the HEAT
and COOL modes. Confirm with
[
SET
]
.
HE AT: With this setting, you can increase or maintain the temperature in the vicinity
of the thermal detector by means of, e.g. a heat pad, heating cable or fan heater.
COOL: In this setting, the temperature can be lowered or maintained with an
external device (e.g. fan, small air-conditioner, air humidifier).
B: The next step defines the daily temperature. Select the required value with
[
+
]
and confirm with
[
SET
]
.
C: Select the night-time temperature and confirm with
[
SET
]
. The start time for the
night-time temperature can be selected with the timer settings (item C).
D: This step defines the temperature difference at which the connected device
switches on or off. Select a value and confirm with
[
SET
]
.
E: You can now select the temperature difference for the alarm function. With
[
SET
]
you close the menu and return to selection A. With
[
OK
]
you terminate the menu and
return to the main view.
6. Timer settings
To enter the temperature menu, press the
[
SET
]
key for 10 seconds.
A: You can set the time with the arrow keys
[
+
]
. With
[
SET
]
you can confirm the
hour setting and change to select the minutes. Confirm your selection again with
[
SET
]
.
Note: Please note that the device does not automatically take into account daylight
savings time.
B: In this stage, select the time from which the daytime temperature is to be activated.
Confirm with
[
SET
]
.
C: Select the start time from which the night-time temperature is to be activated and
confirm with
[
SET
]
.
D: Select the time at which the timer is to switch on the device (TIMER socket) and
confirm with
[
SET
]
. Now select the time at which the device is to be switched off
again and press
[
SET
]
again.
E: (Timers 2-4) Proceed as under item D. If you do not intend to use different switch times,
set the TIMER ON and TIMER OFF to the same settings. After confirming the setting
“TIMER OFF 4”, you return to item A. With
[
OK
]
you terminate the menu and return to the
main view.
Note:
1. Timers 1-3 can be programmed between 00:00 and 23:59. If you wish to leave the
timer switched on beyond 23:59, please use timer option 4.
2. Please check whether the time display works automatically. It may be necessary to
activate the time display relay. To activate the time display relay, please disconnect
the power plug briefly (less than 1 sec) from the socket. The time should start
running now. If the device is disconnected from the socket for a longer period of
time, all settings are reset to the factory settings.
Gebruikshandleiding HortiSwitch
Let op!
1. Dit apparaat is niet geschikt voor inductieve lasten (Zoals bijvoorbeeld voorkomen
bij magnetische voorschakelapparaten). Indien u gasontladingslampen met dit
apparaat wilt aansturen (Zoals bijvoorbeeld HPS of MH lampen) dient u uitsluitend
gebruik te maken van elektronische voorschakelapparaten.
2. Bij levering is de toetsenblokkade van dit apparaat geactiveerd (zie punt 1.
Toetsenblokkade voor het ontgrendelen van de toetsenblokkade)
1. Toetsenblokkade
Als de toetsenblokkade actief is wordt in het display de melding LOC weergegeven. Om
de toetsenblokkade te ontgrendelen drukt u op
[
SET +
]
en houdt u deze combinatie
gedurende 5 seconden ingedrukt. De toetsenblokkade is nu gedeactiveerd. Na twee
minuten zonder activiteit wordt de toetsenblokkade automatisch weer actief.
2. Tonen
Het akoestisch alarmsignaal evenals de toetstonen kan worden geactiveerd of
To Next Page
Loading...