What to do if my Rosen Aviation Monitor doesn't turn on?
If your Rosen Aviation Monitor doesn't turn on, you should: * Check the input power cord connections. * Check the rear line fuse. * Verify the power source is working.
Why doesn't my Rosen Aviation Monitor display video?
If your Rosen Aviation Monitor turns on but doesn't show video, here are a few things to check: 1. Enable and save the video input per Input Port Enable. 2. Check the video source. 3. Check the video cables from the video source to the unit. 4. Check the source selection for the display with the remote control.
Why isn't my Rosen Aviation 42" remote working?
If the remote for your Rosen Aviation Monitor isn't working, try these steps: * Replace the remote batteries with new ones and reprogram the remote. * Make sure that nothing is blocking the infrared sensor on the display.
How to save settings on Rosen Aviation 42" Monitor?
To save settings on your Rosen Aviation Monitor, remember that no settings are saved until SAVE is manually selected from within the menu.
General| Brand | Rosen Aviation |
|---|---|
| Model | 42" |
| Category | Monitor |
| Language | English |
General safety precautions for the display unit.
Precautions related to physical handling and environment.
Compliance with FCC and CE directives for radio frequency energy.
Safety features and material guidelines for the display unit.
Procedures for safely removing the display from its packaging.
Checking included components before installation commences.
Critical warnings and requirements for installing the unit.
Overview of DVI, RGB, Component, S-Video, Composite inputs and their specifications.
RS-232 control and optional interface connections.
Connecting the unit to an earth ground for safety.
Connecting the AC power cord to the unit.
Description of the IR code switch and its function for remote control.
Information about the main user control for the system.
Location of the IR sensor on the display's front panel.
Power, OSD, Source selection, and IR commands.
FlexiScreen, aspect ratio, aperture, PIP modes, and Picture by Picture.
Brightness, Contrast, Hue, Color adjustments, and Display Setup options.
Saving and recalling settings to the unit's memory.
How to clean the display screen safely and effectively.
Importance of cleaning air vents for proper cooling and performance.
Information on the type of fuses used and their replacement.
Preventing phosphor damage by using screen savers.
Troubleshooting steps for power-related issues.
Troubleshooting common issues across all operating modes.
Troubleshooting picture quality and color issues.
Troubleshooting sync and color issues for DVI/RGB inputs.
Troubleshooting sync and color for composite/S-video.
Troubleshooting picture and color issues for YPbPr.2 component video.
Troubleshooting issues with the RS232 interface.
Instructions on how to repack the unit for shipment.
Description of the IR remote buttons and functions.
Instructions for programming and using the SL8000 remote.
Table of keycodes for programming various remote controls.
Overview of menu navigation and RS232 control commands.
Chart of RS232 commands and their syntax for system control.
Commands for controlling Picture-in-Picture features.
Commands for controlling On-Screen Menu (OSM) navigation.
Required setup and parameters for the RS232 communication port.
Outline drawing illustrating the RS232 cable connection.
OSD menus for Composite Y, R, W, S-Video, and their source setups.
OSD menus for DVI, RGB, YPbPr.1, YPbPr.2 inputs.
Gain Control, PIP Control, and FlexiScreen menus.
Display Setup, Color Gamma, Input Ports Enabled, Direct IR Setup menus.
Detailed technical specifications of the display.
Overview of supported user interfaces and inputs.
Supported Picture-in-Picture scenarios and adjustments.
Details on signal processing features like line doublers and scalers.
Electrical and environmental operating conditions and compliance.
Information on the unit's metal packaging and exterior paint.
Defines the purpose of the outline drawing.
Instructions for interpreting the drawing dimensions.
Details on power input, data inputs, and outputs.
Requirements for mounting the unit and ventilation.
To Next Page
