Need help?Do you have a question about the Rosendahl nanosyncs HD and is the answer not in the manual?
Controls unit power and indicates status for video/audio references, SD/HD generators, and sample rates.
Shows selected video reference (INTERNAL, EXT. PAL, EXT. NTSC, EXT. TRI LEVEL) and detected frame rate.
Configures SD sync generator output to NTSC, PAL 25, or slow PAL 24/23.98.
Configures HD tri-level sync generator output standards (1080i/psf, 1080p, 720p) and frame rates.
Assigns SD or HD signals to individual video outputs (VO1-VO6).
Selects reference for word clock and AES/SPDIF audio (FOLLOW VIDEO, EXT. WORD FS, etc.).
Shows base sample rate (44.1/48kHz) and pull up/down rates.
Sets multipliers (x2, x4, x256) for clock outputs (WO1-8, AES/SPDIF).
Indicates LTC/MTC translation status and configuration protection mode.
Controls for menu navigation, parameter changes, and storing settings.
Six BNC outputs (VO1-VO6) for SD/HD sync signals.
BNC input (C7) for genlocking to external SD/HD video references.
BNC input (C8) for external word clock signals.
RCA connectors (C9, C10) for LTC time code input and output.
USB 2.0 port (C11) for MIDI communication with host computers.
BNC, XLR, and RCA connectors (C12-C22) for clock outputs.
IEC socket (C23) for mains power connection.
Uses internal 0.5 ppm crystal oscillator as master reference.
Locks to external PAL video reference signal via input connector.
Locks to external NTSC video reference signal via input connector.
Locks to external Tri Level Sync signal via input connector.
Sets SD generator output to NTSC, PAL 25, or PAL 24 standards.
Sets HD tri-level standard and frame rate (e.g., 1080i/psf x2).
Selects base frame rate for the HD generator (e.g., 24 fps, 30 fps).
Configures individual video outputs (VO1-VO6) for SD or HD signal.
Audio clock generator follows the selected video reference.
Resolves to external word clock frequency, allowing sample rate conversion.
Regenerates incoming word clock sample rate 1:1 for high quality distribution.
Resolves audio word clock signals to external LTC time code.
Sets the base sample rate to 44.1 or 48kHz.
Compensates for frame rate differences using special sample rates.
Configures multipliers (x2, x4, x256) for clock outputs.
Manually start/stop the internal LTC time code generator.
Supports various FPS standards (23.98, 24, 25, 29.97, 30).
Unit syncs to incoming time code if standards match.
USB 2.0 port for MIDI communication, compliant with USB MIDI Devices spec.
Translates incoming LTC time code to MTC for USB output.
Synchronizing Digital Audio Workstations (DAWs) to the unit using MTC.
Controls the LTC generator using Midi Machine Control (MMC) commands.
Triggers internal LTC generation from incoming MTC signals.
Prevents unwanted changes by disabling keys in protected mode.
Firmware version displayed on startup via LEDs.
Procedure to update firmware using nanoSETUP software.
Free utility for configuring nanosyncs units.
Controls for video reference, audio reference, sample rate, etc.
Adjusts black level of SD NTSC sync signals to +7.5 IRE.
Controls subcarrier tracking for PAL/NTSC references.
Outputs bi-level sync on VO6 for Dolby Encoders/Decoders.
Outputs specific square wave signals on WO8.
Generates non-standard sample rates locked to video reference.
Controls the LTC generator using nanoSETUP utility.
Adjusts H-phasing for external references.
Details for USB, video, word clock, LTC, SPDIF, AES/EBU connectivity.
Sample rates, multipliers, lock ranges, internal time base accuracy.
Supported SD and HD video sync standards and frame rates.
Power input requirements and unit physical size.
Ports & Interfaces| USB | USB 2.0 |
|---|---|
| video input | BNC, 75 ohms terminated |
| word clock input | BNC female, 75 ohms terminated, 1.5 - 5 Vpp, 40 - 200 kHz |
Audio Interfaces| time code LTC input | RCA/ Cinch 10k ohms, -40 to +20 dBu |
|---|---|
| time code LTC output | RCA/ Cinch 600 ohms, 1 Vpp |
| SPDIF output | RCA 75 ohms, 0.5 Vpp, IEC 985 |
Video Outputs| video outputs | 6 x BNC 75 ohms, AC-coupled |
|---|---|
| standard definition video sync | 525/29.97 NTSC, 625/25 PAL |
| high definition video sync | 1080p23.98, 1080p24, 1080p25, 1080p30, 1080p50, 1080p59.94, 1080p60 |
Power| power supply type | internal linear regulated |
|---|---|
| power supply voltage | 230 VAC / 50 Hz or 115 VAC 60 Hz |
| power consumption | 10 W |
Weight and Dimensions| rackmount size | 19", 1U |
|---|---|
| dimensions | 442 x 120 mm |
| weight | 2.5 kg |
To Next Page