EasyManua.ls Logo

Rostra GlobalCruise - User Manual

Rostra GlobalCruise
24 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GLOBALCRUISE
ELECTRIC CRUISE CONTROL
UNIVERSAL APPLICATION
INSTALLATION & O
WNER’S MANUAL
CONTENTS
SAFETY PROCEDURES ......................................... 2
HELPFUL HINTS................................................. 4
P
ARTS LIST...................................................... 5
PARTS DIAGRAM................................................ 6
S
UPPLEMENTAL
PARTS......................................... 7
S
WITCH
SETTINGS.............................................. 8
INSTALLATION ................................................... 9
TROUBLESHOOTING............................................. 20
WARRANTY....................................................... 23
O
PERATING INSTRUCTIONS ................................... 24
Form #4565, Rev. D, 05-14-02
Question and Answer IconNeed help?

Do you have a question about the Rostra GlobalCruise and is the answer not in the manual?

Summary

SAFETY PROCEDURES

HELPFUL HINTS

PARTS DIAGRAM

SUPPLEMENTAL PARTS

SWITCH SETTINGS

INSTALLATION

I. CRUISE MODULE MOUNTING

Steps for selecting a location and mounting the cruise module.

II. MEASURING THROTTLE CABLE TRAVEL

Measure throttle cable travel to ensure proper connection and prevent damage.

III. ATTACHING CRUISE CABLE TO THROTTLE

Methods for attaching the cruise cable to the throttle assembly.

B. Pulley Assembly (Dual) Using The T-BAR ADAPTOR

Attaching cruise cable using a T-Bar Adaptor to the pulley segment.

C. Pedal Attachment

Attaching the cruise cable to the accelerator pedal shaft.

D. Ford Throttle

Attaching cruise cable to Ford vehicle throttle.

E. General Motors and Chrysler Throttle using THREE BEAD CONNECTOR

Attaching cruise cable to GM/Chrysler throttle using a three bead connector.

F. General Motors, Ford and Chrysler Throttle using Stud-Clip w Cable

Attaching cruise cable to GM/Ford/Chrysler throttle using a stud-clip.

IV. ANCHORING CRUISE CABLE

Methods for anchoring the cruise control cable to the vehicle.

A. SNAP-IN ADAPTOR

Anchoring cruise cable using a snap-in adaptor.

B. General Motors Blank Anchor

Anchoring cruise cable to GM vehicles using a blank anchor point.

C. FLAG NUT

Anchoring cruise cable using a flag nut.

V. CRUISE HARNESS

Routing and connecting the cruise control wiring harness.

VI. SEALING BULKHEAD

Sealing the bulkhead opening after passing the harness through.

VII. CONTROL SWITCH INSTALLATION

Instructions for installing the cruise control switch.

VIII. WIRING ATTACHMENTS TO VEHICLE

Connecting the cruise control wiring to vehicle components.

A. Black Ground Wire

Locating and connecting the ground wire for the cruise system.

B. Brown Accessory Power

Connecting the brown wire to accessory power.

C. Red Brake Positive

Connecting the red wire to the positive side of the brake switch.

D. Violet Brake Negative

Connecting the violet wire to the negative side of the brake switch.

E. Dark Blue Tachometer (TACH) Wire

Connecting the dark blue TACH wire for safety features.

F. Gray Vehicle Speed Sensor (VSS) Wire

Connecting the gray VSS wire for vehicle speed sensing.

G. Light Green Neutral Safety (NSS)

Connecting the light green NSS wire for safety.

H. Orange Enable Output (ENO) Wire

Connecting the orange ENO wire for external wheatlamp control.

J. Auxiliary Speed Sensor Connector

Utilizing connector for an auxiliary speed sensor.

K. 4-Pin Switch Connector

Connecting the 4-pin connector for the control switch.

L. 2-Pin Switch Connector

Connecting the 2-pin connector for additional switch functions.

M.Bulkhead Connectors

Using bulkhead connectors to pass harness through firewall.

N. GlobalCruise Servo Connector

Connecting the GlobalCruise servo connector.

TROUBLESHOOTING

IX. SELF DIAGNOSTIC TESTING PROCEDURE

Procedure to enter self-diagnostic mode for testing system functions.

X. TACH SIGNAL TESTING PROCEDURE

Procedure to test the TACH signal for proper operation.

XI. CONTROL SWITCH TESTING PROCEDURE

Continuity charts to test the functionality of the control switch.

WARRANTY

OPERATING INSTRUCTIONS

XII. GlobalCruise OPERATING INSTRUCTIONS

Detailed steps for operating the GlobalCruise system.

THINGS YOU SHOULD KNOW ABOUT YOUR GlobalCruise

Key information regarding GlobalCruise performance and limitations.

Rostra GlobalCruise Specifications

General IconGeneral
TypeCruise Control System
InstallationProfessional Installation Recommended
Featuresresume function
Control MethodSteering Wheel Controls (Vehicle Dependent)
CompatibilityUniversal (compatible with most vehicles)