50
MMAAIINNTTEENNAANNCCEE PPRROOCCEEDDUURREESS
This section includes instructions for
basic maintenance procedures.
WWAARRNNIINNGG
TTuurrnn ooffff tthhee eennggiinnee aanndd ffoollllooww
tthheessee mmaaiinntteennaannccee pprroocceedduurreess
wwhheenn ppeerrffoorrmmiinngg mmaaiinntteennaannccee.. IIff
yyoouu ddoo nnoott ffoollllooww pprrooppeerr mmaaiinnttee--
nnaannccee pprroocceedduurreess yyoouu ccaann bbee iinn--
jjuurreedd bbyy hhoott ppaarrttss,, mmoovviinngg ppaarrttss,,
eelleeccttrriicciittyy,, cchheemmiiccaallss oorr ootthheerr
hhaazzaarrddss..
WWAARRNNIINNGG
SShhoouulldd rreemmoovvaall ooff aa lloocckkiinngg ddee--
vviiccee ((ee..gg.. lloocckk ttaabbss,, sseellff--lloocckkiinngg
ffaasstteenneerrss,, eettcc..)) bbee rreeqquuiirreedd,, aall--
wwaayyss rreeppllaaccee wwiitthh aa nneeww oonnee..
NNOOTTIICCEE
NNeevveerr lleeaavvee aannyy oobbjjeecctt,, rraagg,, ttooooll,,
eettcc..,, iinn tthhee eennggiinnee ccoommppaarrttmmeenntt oorr
iinn tthhee bbiillggee..
FFuueell RReeqquuiirreemmeennttss
To learn about the fuel requirements
for your
Rotax E-TEC
outboard en-
gine, refer to
Boat Information
.
IInnjjeeccttiioonn OOiill RReeffeerreennccee
To learn about the injection oil require-
ments for your
Rotax E-TEC
outboard
engine, refer to
Boat Information
.
PPrriimmiinngg tthhee OOiill SSyysstteemm
The oil systems of
Rotax E-TEC
out-
board engines are primed at the
factory.
Priming the oil system is only required
if:
– The oil system has been disas-
sembled for servicing or parts
replacement
– The oil tank has run out of oil
NNOOTTEE:: If the oil tank has run out of
oil, the
EMM
will activate SHUT
DOWN mode, set the appropriate fault
code, and display the NO OIL
warning.
After refilling an empty oil tank or serv-
icing the oil system, air MUST be re-
moved from the oil system before
operating the outboard.
Prime the oil system by performing
the
Long– Term Storage (Winteriza-
tion)
procedure —TWO times.
If available,
BRP Marine Diagnostics
software may be used to prime the oil
system ONE time.
GGeeaarrccaassee
GGeeaarrccaassee LLuubbrriiccaanntt RReeppllaacceemmeenntt
1. Ensure that the Gearcase Anti--
Ventilation (AV) plate is level.
2. Adjust the outboard trim angle until
the Gearcase AV plate is +15 de-
grees from the level position.
WWAARRNNIINNGG
GGeeaarrccaassee lluubbrriiccaanntt mmaayy bbee uunnddeerr
pprreessssuurree aanndd//oorr hhoott iiff oouuttbbooaarrdd
wwaass rreecceennttllyy ooppeerraatteedd oorr iiff ggeeaarr--
ccaassee lluubbrriiccaanntt iiss aabboovvee tthhee MMaaxxii--
mmuumm lleevveell..
WWeeaarr ssaaffeettyy ggllaasssseess aanndd ttaakkee pprree--
ccaauuttiioonnss ttoo aavvooiidd iinnjjuurryy wwhheenn rree--
mmoovviinngg vveenntt pplluugg..
3. Open the gearcase vent plug.
To Next Page
Loading...
Need help?
General