RouterBOARD MikroTik mAP 2nD - User Manual

RouterBOARD mAP
Quick Setup Guide and Warranty Information
The mAP is a small AP device with 2 ethernet ports, Ether1 supports powering by PoE, ether 2 supports PoE output for powering
another device.
Connecting
1. Connect your Internet cable to port 1, and your PC to port 2. If using the mAP to power another router using the PoE
output feature, connect the router to Ether 2, and use the built in wireless AP to configure the mAP
2. Set computer/router IP configuration to automatic (DHCP)
3. Wireless AP mode is enabled by default, you can connect to the SSID “MikroTik”. Log into your router from your web
browser by opening 192.168.88.1 in the address bar
4. The Ether 2 port suports PoE output, with auto detection feature. This means you can connect Laptops and other non-
PoE devices without damaging them. The PoE on Ether2 outputs approximately 2V below input voltage, and supports up
to 0.5A (So provided 24V PSU will provide 22V/0.5A output to the Ether2 PoE port).
Powering
The device accepts powering from the power jack or from the first Ethernet port (Passive PoE):
 DC power jack (5.5mm outside and 2mm inside diameter, female, pin positive plug) accepts 8-57V DC
 The first Ethernet port accepts passive Power over Ethernet 8-57V DC.
 mAP can also be powered with the built in microUSB port, using the USB 5V power
Under maximum load, the power consumption of this device is 4W (when not using PoE output)
Booting process
The device is preinstalled with MikroTik RouterOS software. It can be configured in several ways.
This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet
cable. Connect to wireless SSID “MikroTik” and open 192.168.88.1 in your web browser. Username is admin and
there is no password. In case IP connection is not available, Winbox can be used to connect to the MAC address of
the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of
the device when starting it until the LED light turns off, then release the button and the device will start looking for
Netinstall servers.
By default, the device is preconfigured with a simple firewall on the WAN port, this configuration can be viewed when
first connecting to the Router via Winbox. It will ask whether to keep this configuration or clean it to use your own.
LAN/WLAN ports have DHCP server enabled.
Extension Slots and Ports
 Two 10/100 Ethernet ports, supporting automatic cross/straight cable connection (Auto MDI/X), so you can use either
straight or cross-over cables for connecting to other network devices.
 One Integrated Wireless 2.4GHz 802.11b/g/n 1x1 MIMO, Onboard PIF antennas, max gain 1.2dBi
 One microUSB 2.0 port
Resetting the device
In case you wish to return the device to its original configuration, you can use the RESET button which is located to
the left of the Ethernet ports. Hold this button during boot time until LED lights start flashing, then release the button
to reset RouterOS configuration. You can use this procedure if you have forgotten the password to access the
device, or simply wish to return the unit to its default configuration state.
 
https://arttel.ru/
https://arttel.ru/

Summary

Quick Setup Guide

Connecting the Device

Guide to connecting the mAP device, including internet and PoE connections.

Powering the Device

Details on powering the mAP via DC jack, PoE, or microUSB, and its power consumption.

Booting Process and Initial Setup

Explanation of the boot sequence and initial configuration via Ethernet or Netinstall.

Hardware Ports and Expansion

Overview of the device's physical ports, including Ethernet and microUSB.

Device Reset Procedure

Instructions on how to reset the mAP device to its default configuration.

Buttons and Reset Functions

Reset Button Operations

Details the three distinct functions of the reset button based on hold duration.

Operating System Support

Specifies the supported MikroTik RouterOS versions for the device.

Copyright and Warranty

Provides copyright details, hardware warranty terms, and RMA procedure.

FCC Interference Statement

FCC Compliance Requirements

Outlines FCC compliance, rules, and conditions for device operation.

RF Exposure Guidelines

Specifies minimum distances for FCC RF exposure compliance.

CE Declaration of Conformity

English Conformity Statement

States that the ROUTERBOARD complies with essential requirements of Directive 1999/5/EC.

Multilingual Setup Instructions

Provides multilingual instructions on initial setup and configuration via web browser.

RouterBOARD MikroTik mAP 2nD Specifications

General

Model	mAP 2nD
Category	Wireless Access Point
CPU nominal frequency	650 MHz
Size of RAM	64 MB
Storage size	16 MB
Storage type	FLASH
Operating system	RouterOS
Wireless Standards	802.11b/g/n
Wireless Frequency	2.4 GHz
Max Data Rate	150 Mbps
Ethernet ports	1
PoE out	No
PoE in	Yes
Power Input	5V