Rowe 7800 Deluxe Series

Need help?

Do you have a question about the Rowe 7800 Deluxe Series and is the answer not in the manual?

Summary

Section 1: INSTALLATION

UNPACKING

Steps for unpacking the snack vendor and checking for damage.

SET-UP INSTRUCTIONS

Procedures for moving, leveling, and connecting the vendor.

BILL ACCEPTOR DIP SWITCH SETTINGS

Configuration of bill acceptor dip switches for proper operation.

Section 2: Description

INTRODUCTION

Overview of the 7800 Deluxe family of snack/candy vendors.

PRODUCT SHELVES

Details on universal, candy, pastry, and dual helix shelf configurations.

HORIZONTAL GUM AND MINT UNIT

Description and operation of the gum and mint vending unit.

COIN MECHANISM (DOMESTIC)

Information on coin mechanisms and their installation.

Special Vending Modes

Explanation of features like Promotional Vend, Multivend, and Smart Shopper.

MANAGEMENT INFORMATION SYSTEM (MIS) DATA

Details on sales and credit information tracked by the controller.

Section 3: Program Operation

DIAGNOSTIC MODE

Procedures for checking and clearing machine errors.

SERVICE MODE OPERATION

Accessing and navigating through the machine's programming menus.

KEY 1 - Load;Dispense;Calibrate the Changer Tubes

Managing coin tube inventory and calibration.

KEY 5 - Manual Peripheral Configuration

Setting up credit system parameters like cash system type.

KEY 7 - Point-of-Sale Message Serial Number

Programming POS messages, serial, ID numbers, date, and time.

KEY 0 - Motor Count Test Vend, and Hopper Setup

Testing motors and configuring the bulk coin hopper.

Section 4: Troubleshooting

TROUBLESHOOTING PROCEDURES

General guidelines for diagnosing and resolving machine malfunctions.

Troubleshooting Chart 4-1 Error Messages

Lists common error messages and their probable causes/solutions.

Troubleshooting Chart 4-2 Problem;Solution

Details common problems and their potential causes and solutions.

Troubleshooting Chart 4-3 Rowe Bill Acceptor

Specific troubleshooting for the Rowe Bill Acceptor.

15 Pin Coin Mech Socket

Pinout and compatibility information for coin mechanisms.

Section 5: Maintenance

CLEANING

Procedures for cleaning the vendor's display window and surfaces.

REMOVAL AND REPLACEMENT

Instructions for removing and replacing key vendor components.

Single Selection Helix

Steps for removing and replacing a single selection helix coil.

Dual Selection Helix

Steps for removing and replacing dual helix coils.

GUM AND MINT UNIT REMOVAL

Procedures for removing the gum and mint unit assembly.

Section 7: PARTS CATALOG

ORDERING REPLACEMENT PARTS

Information required for ordering replacement parts from distributors.

OPTIONAL KITS

List of optional kits available for the vendor.

Fig. 1 Main Door Trim and Panels

HORIZONTAL PANELS

Lists horizontal panel options and their finishes.

VERTICAL PANELS

Lists vertical panel options and their finishes.

Fig. 2 Main Door Exterior

Fig. 3 Main Door Interior

Fig. 4 Delivery Box Assembly

Fig. 5 Cabinet Assembly Components with Refrigeration Unit

Fig. 5 a Cabinet Assembly Components with Bill Changer

Fig. 6 Power Panel Components

Fig. 7 Shelf Support and Plug Assemblies

Fig. 8 3, 4, or 5 Selection Shelf Assembly

Fig. 9 Dual Helix Shelf

Fig. 10 Candy Shelf

Fig. 11 Gum and Mint Unit

Fig.12 Refrigeration Unit (Optional)

Fig.13 Main Controller Circuit Board Assembly

Fig.14 Dispenser and Chute MTG Bracket Assembly

Fig.15 Coin Dispenser Assembly

Fig.16 Display Board

Fig.17 Harness List

Section 6: TROUBLESHOOTING & SELF-DIAGNOSTICS

MISCELLANEOUS PROBLEMS

General issues not related to specific fault codes.

ERRATIC PAYOUT

Inconsistent dispensing of the correct number of coins.

COIN COUNTING PHOTOTRANSISTOR (SENSOR) CHECK

Procedure to test the coin detector sensor.

LOW COIN SENSOR ELECTRICAL CHECK

Testing the function of the low coin sensor.