Rule A53S User Manual

Congratulations
Congratulations!
You have just purchased one of the finest quality pumps
available in the industry. It was developed after years
of experience, research and testing by our research
staff. Its motor, electronics and seals were specifically
designed and manufactured by Rule Industries to give
years of reliable, trouble-free performance.
How This Pump Works
Rule Automatic Sump and Utility Pumps turn on and check
for water approximately every 2-1/2 minutes. During this
“check”, the pump runs for about one second and checks for
resistance or drag against the impeller. If resistance (water)
is found, it will run for as long as water is present. When all
the water is pumped out, the pump shuts off and returns to
its 2-1/2 minute test cycle. The pump can be started at any
time by disconnecting it from the power source, waiting five
seconds and reconnecting.
Please read and follow the instructions carefully and your
pump will provide you with the maximum output for which
it was designed.
Thank You for Purchasing a Rule Pump
All returns must be shipped to:
Rule Industries, Inc.
Cape Ann Industrial Park
Gloucester, MA 01930
M-681 Rev D 3/08
This pump has only been tested for use
as a submersible sump pump and for
draining pool covers.
FULLY
AUTOMATIC
PUMP
IN
S
TR
UC
TI
O
N
G
UIDE
Symptom Possible
Cause
Cure
Pump only
runs for a
few seconds
Clogged
strainer or
jammed
impeller
Blocked
discharge line
Pump does
not run
Pump runs,
but does not
pump water
Electrical
connections
Air lock
Insufficient
water
The automatic control system
tests for water approximately
every few minutes. If the water
level detected is only about 3/4",
the pump will shut off after a
few seconds. Every few minutes
thereafter, it will automatically
check the water level and will
only continue pumping if suf-
ficient water is present.
Disconnect pump from power
source and remove strainer (some
models contain stainless steel
inner strainers). Remove debris
from strainer(s) and surrounding
area. Remove any debris from
the impeller.
Disconnect pump from power
source and remove blockage from
pipes/hoses and discharge port.
Check electric receptacle for
power. Check fuse and/or cir-
cuit breaker. Is the receptacle
a three prong grounded outlet
in good condition? Is the plug
making good contact in the
receptacle?
Check discharge hose. Is it
running level or continuously
downwardly once the hose
starts downwardly? Are
there any loops in the hose?
Trouble Shooting
The following is a list of common problems that may
cause your pump to work improperly. If you feel that your
pump is malfunctioning due to other reasons please call
our customer service department at 978-281-0573
The Rule Guarantee
We guarantee all
our pumps from factory
defect or malfunction
for three full years from
purchase date.
Models A53S, A53S-24
1800 GPH, 110 VAC, 60HZ, 1.0 AMP
Thermally Protected
Enclosure 3
®

Rule A53S Specifications

General

Outlet Diameter	1 inch
Housing Material	Cast Iron
Impeller Material	Brass
Seal Type	Mechanical Seal
Phase	Single Phase

Summary

Trouble Shooting

Pump Runs Briefly, Then Stops

Automatic control tests water level; shuts off if level is low, then re-checks periodically.

Clogged Strainer or Jammed Impeller

Disconnect power, remove strainer, and clear debris from strainer(s) and impeller.

Blocked Discharge Line

Disconnect power, remove blockage from pipes/hoses and discharge port.

Pump Does Not Run

Check electrical receptacle, fuse/breaker, outlet condition, and plug contact.

Pump Runs, No Water Output

Check discharge hose for level placement, no downward sags or loops trapping air.

The Rule Guarantee

How The Pump Works

Pump automatically checks water level every 2.5 mins; runs when water is present, shuts off when empty.

Important Safety Instructions

General Safety Precautions

Includes warnings about children, electric shock, GFCI, cord placement, and avoiding damp surfaces.

Installation Instructions

Pump Placement and Hose Setup

Determine pump location for sump/utility or pool cover use, ensuring proper drainage and no hose loops.

Strainer Attachment and Mounting

Position strainer, attach to base (wood or concrete), and snap pump onto strainer securely.

Discharge Hose Connection

Use correct hose/pipe size (1-1/8" I.D. or 1" pipe) for optimal flow, avoiding restrictions.

Performance and Maintenance

Break-in Period

A break-in period of up to 10 hours is required to achieve maximum pumping capacity.

Periodic Maintenance

Keep strainers clean and free of debris for optimal performance. Remove debris around plastic and internal strainers.

Freezing or Impeller Jamming

Pump has protective circuit; it will resume operation when ice thaws or debris is removed.