Runva KLS-203 - User Manual

To Next Page

KLS-203 Wireless Winch Remote Control Kit

RUNVA wireless remote works lets you operate your winch from up to 75 ft without

cables or switches. Just press the remote transmitter and you're ready to operate your winch

Start, stop, in or out.

◆ Remote range up to 75 ft.

◆ Transmitter equipped with long life.

◆ Battery and power saver circuit.

◆ Transmitter & receiver.

◆ Visual indicator light shows remote operation.

◆ Additional transmitters available tooperate receiver.

◆ Installs in minutes.

◆ Transmitter replacement batteryreadily available.

WARNING: The Wireless Remote is designed for use on front mount self-recovery winches

only. The remote is not designed for and should not be used on winches or hoists in

industrial applications (commercial car haulers/carriers, wreckers, cranes, etc.) or for any

other remote controlled applications.

Type:

RWRC①－②－③－④－⑤

①：Signed as 01, 02. ”01”: Code learning Type; “02”: Code Fixed.

②：Using Range admitted. Signed as E, C.”E” : European Using Style;

”C” Common style, this letter is always leave out;

③：Power Voltage, Signed as 12VDC or 24VDC.

④：Connector Style, using solely out of the winches control box. Signed as 03, 04. “03” :

three cores connector;

“04” : four cores of connector.

⑤: mount type, Signed as 05.

“05” :small remote can fix in the winches control box.

Part List:

1. one transmitter.

2. one receiver with three or four cores of line with connector.

Installation and operating instructions:

There are two kinds of different connect way for the reason of different kinds winches’

solenoid female connector. You can choice a suitable type of wireless remote control as

RWRC－03 or RWRC－04. showing as the following connection drawing.

RWRC－03: While you insert the receiver plug to the winches’ solenoid female connector,

you shold connect the earth line to the battery negative. Be sure of the earth line connect

exactly, then you can operate your winch by press the button on the transmitter.

RWRC－04: While you are ready to operate a winch, just connect the four cores of the

recever to the winches’ solenoid female connector. And then you can operate your winch by

press the button on the transmitter. NOTE: Make sure one of the four pole receptacle is

connected to earth.

“03”,”04”connection drawing:

To Battery

Earth Line

"03" Type

"04" Type

Receiver

Transmitter

female connector

solenoid control box

antenna

Need help?

Do you have a question about the Runva KLS-203 and is the answer not in the manual?

The KLS-203 Wireless Winch Remote Control Kit allows you to operate your winch wirelessly from up to 75 feet away, eliminating the need for cables or switches. Simply press the remote transmitter to control your winch's start, stop, and direction (in or out).

Function Description:

The device consists of a transmitter and a receiver. The transmitter sends wireless signals to the receiver, which then controls the winch's solenoid. It is designed for use with front-mount self-recovery winches only and is not intended for industrial applications such as commercial car haulers/carriers, wreckers, cranes, or other remote-controlled applications.

Important Technical Specifications:

Wireless Range: Up to 75 feet.
Power Voltage: Available in 12VDC or 24VDC options, as indicated by the "RWRC-X-X-X-3" or "RWRC-X-X-X-4" designation.
Connector Styles:
- "03": Three-core connector, used solely with the winch's control box.
- "04": Four-core connector, used solely with the winch's control box.
Mount Type: "05" indicates a small remote that can be fixed within the winch's control box.
Code Learning Type: "01" for code learning, "02" for fixed code.
Usage Range: "E" for European style, "C" for common style (often omitted).

Usage Features:

Easy Installation: The kit installs in minutes.
Visual Indicator: A light on the transmitter shows when it is operating.
Long Battery Life: The transmitter is equipped with a long-life battery and a power saver circuit.
Multiple Connection Options: Two main connection types are available:
- RWRC-03: Requires inserting the receiver plug into the winch's solenoid female connector and connecting the earth line to the battery negative.
- RWRC-04: Requires connecting the four cores of the receiver to the winch's solenoid female connector. Note: One of the four-pole receptacles must be connected to earth.
Mounting Flexibility: The "05" type allows the receiver to be mounted inside the winch's control box for a more integrated setup.
Operating Procedure:
1. Disengage the winch clutch.
2. Pull out about 1.5 meters of winch wire rope.
3. Reengage the winch clutch.
4. Insert the remote control receiver plug into the winch's solenoid control box female connector. For RWRC-03 type, ensure the black earth line is properly connected to the battery negative.
5. Place the receiver in a suitable location.
6. Keep the receiver's antenna extended and straight.
7. Pull out the transmitter's antenna and move down its cover to expose the control button.
8. Press the button to operate the winch (start, stop, in, out).

Maintenance Features:

Replaceable Battery: The transmitter battery is readily available for replacement.
Troubleshooting Guide: The manual provides a comprehensive troubleshooting section to address common issues:
- Motor turns, but Winch does not work: Suggests checking winch operating instructions for a defective winch.
- Motor does not turn, but "Click" sound is heard in receiver: Indicates possible loose receiver connections to the winch or a false earth line connection. Suggested actions include reinserting connections and ensuring proper earth connections.
- Motor runs in one direction only: Points to a defective winch or loose receiver connections. Suggested actions include checking winch operating instructions and reinserting connections.
- No actions (no response from winch): Suggests that the receiver and transmitter are not matching. For "01" (code learning) type, a code learn procedure is recommended. For "02" (fixed code) type, returning to the manufacturer for rematching is advised.

FCC Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The equipment has been tested and found to comply with the limits for a Class B digital device, designed to provide reasonable protection against harmful interference in a residential installation. If the equipment causes harmful interference to radio or television reception, users are encouraged to try to correct the interference by reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, connecting the equipment to a different circuit outlet, or consulting a dealer or experienced radio/TV technician.

Runva KLS-203 Specifications

General

Brand	Runva
Model	KLS-203
Category	Remote Control
Language	English