Russell Hobbs RHBL2000 User Manual

5
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
In use, treat the jug and blade unit as a single unit.
1. Sit the motor unit on a stable, level surface.
2. Lower the jug onto the motor unit.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t fill past the 1500 ml mark. If you do, the contents may
force the lid off when you start the motor.
5. Replace the lid with the cap on. Don’t operate the appliance without fitting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the
symbol
to indicate that it is in standby mode. Tap
to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The following table lists the controls and gives a brief overview of their function.
Button Function
Standby. Tap to switch your blender in or out of standby mode.
Stop. Tap to stop blending, or to stop the currently active program.
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
Highest speed. Tap to set the speed control to its maximum setting.
Lowest speed. Tap to set the speed control to its minimum setting.
Ice crush/Pulse - for crushing ice or fine blending control.
Smoothie - blend fresh or frozen fruits and other ingredients into thick smoothies.
Icy drink - liquefy frozen drinks.
Soup - Use for preparing soup ingredients. Hot liquids/ingredients should
never be placed in the blending jug
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the flashing
icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap
at any time.
• To change the speed, swipe or tap the slider control at any time. Tapping + will change to
the highest speed; tapping – will change the speed to the lowest speed.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.
4
BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.
PREPARATION
1. Sit the motor unit on a stable, level surface.
2. Lower the jug on to the motor unit. You cannot operate your blender unless the jug is
correctly placed onto the motor unit. This is a safety feature.
3. Remove the lid.
4. Put the ingredients into the jug. Don’t ll past the 1500 ml mark. If you do, the contents may
force the lid o when you start the motor.
5. Replace the lid. Don’t operate the appliance without tting the lid.
6. Put the plug into the power socket.
CONTROLS
When you connect your blender to the mains supply, the control panel will show the C symbol
to indicate that it is in standby mode. Tap C to activate the control panel. The control panel is a
touch screen. After 30 seconds of inactivity, your blender will revert back to the standby state.
The folowing table lists the controls and gives a brief overview of their function.
Button Function
C
Standby. Tap to switch your blender in or out of standby mode.
@
Stop. Tap to stop blending, or to stop the currently active program.
+
Start. Tap to start blending, or to start the selected program.
Slider control. Swipe left or right to select or modify the speed. Tapping the
slider control along its length will move the speed control to the point where
you tap.
+
Highest speed. Tap to set the speed control to its maximum setting.
–
Lowest speed. Tap to set the speed control to its minimum setting.
*
Ice crush/Pulse - for crushing ice or ne blending control.
%
Smoothie - blend frozen fruits and other ingredients into thick smoothies.
^
Icy drink - liquefy frozen drinks.
&
Soup - use for making soups.
MANUAL OPERATION
You can start, stop, pulse and choose the speed of your blender manually to suit the ingredients
you are processing.
1. Tap C to activate the control panel.
2. Swipe or tap the slider control to the desired speed.
3. Tap the ashing + icon to start your blender. Your blender will start at the selected speed.
• To stop blending, tap @ at any time.

Russell Hobbs RHBL2000 Specifications

General

Brand	Russell Hobbs
Model	RHBL2000
Category	Blender
Language	English