What to do if there is no hot water coming out of my RVMP flexTEMP FG-SBMC-11?
If the hot water faucet is turned ON, but no hot water is coming out of your RVMP Water Heater, make sure the gas valve and water inlet valve are open. Also, check if the water supply has been interrupted and restore it. Ensure the hot water faucet is completely open. If the appliance is frozen, allow it to thaw.
Why does the water temperature not increase on my RVMP Water Heater?
If the water temperature of your RVMP Water Heater isn't increasing when you adjust the temperature setting, ensure the gas valve and water inlet valve are fully open. If the inlet water is too cold, try reducing the temperature setting. Additionally, reduce water flow by turning off a faucet or partially closing a valve.
How to fix E8 error on RVMP Water Heater?
If you experience the E8 error on your RVMP Water Heater, it might indicate an air pressure switch failure. First, check the fan's electrical connections and ensure it's functioning correctly. Then, remove any debris blocking airflow. Inspect and repair or replace any faulty electrical connections to the air pressure switch. If needed, replace the air pressure switch.
How to troubleshoot E7 error on RVMP flexTEMP FG-SBMC-11 Water Heater?
If you see the E7 error on your RVMP Water Heater, it could mean a failure with the gas inlet valve. Inspect and repair or replace any damaged electrical connections to the gas valve. If the connections are fine, the gas valve itself might be bad and require replacement.
Why does hot water not flow immediately from my RVMP Water Heater?
If the hot water from your RVMP Water Heater doesn't flow immediately when you open the faucet, simply wait. It takes a moment for the appliance to start and for any cold water in the lines to clear out.
What to do if my RVMP flexTEMP FG-SBMC-11 shows En Timeout function?
If your RVMP Water Heater displays the error code En, simply turn the appliance off and then back on.
What to do if RVMP flexTEMP FG-SBMC-11 flame sensor is sensing flame before ignition?
If the flame sensor of your RVMP Water Heater is sensing a flame prior to ignition, it's likely due to a bad flame sensor or a short. Replace the flame sensor.
Why is my RVMP Water Heater not heating when the faucet is slightly open?
If the hot water faucet is slightly open and the water coming out of your RVMP Water Heater isn't hot, it's because the appliance turns off when the minimum flow rate is reached (2.8 L/min or 0.74 Gallons/min). Open the hot water faucet further to increase the flow rate beyond the minimum, so the appliance turns on.
Why is the hot water from my RVMP flexTEMP FG-SBMC-11 white and cloudy?
If the hot water dispensed from your RVMP Water Heater is white and cloudy, this is normal. It's caused by tiny bubbles that develop from air in the water as it's rapidly heated.
Why is there white smoke from my RVMP Water Heater exhaust in cold weather?
If you notice white smoke coming from the exhaust of your RVMP Water Heater in cold weather, this is normal. It's just water vapor in the exhaust gas becoming visible in the cold air.
Welcomes the user and introduces the product.
Highlights severe risks like fire, explosion, personal injury, or death from improper use.
Provides essential steps to follow in case of a detected gas leak.
Details safe operating conditions, ventilation, and obstruction avoidance.
Outlines operator responsibilities for health, safety, water quality, and maintenance.
Procedures to ensure appliance safety before and during vehicle transit.
Visual representations of the water heater's external appearance.
Overview of the water heater's internal layout.
Close-up view of specific internal components.
Diagram of the control board and its component arrangement.
Table listing components with their type, model, and technical data.
Further details on components like gas control, thermostats, relays, and MCUs.
Describes microcomputer control, variable temperature, and digital adjustments.
Covers the remote LCD display and over-pressure protection system.
Lists multiple built-in safety features for various fault conditions.
Comprehensive list of technical data including dimensions, weight, and connections.
Schematic illustrating electrical connections for the appliance.
Visual representation of the appliance disassembled into its parts.
Numbered list identifying each part shown in the exploded view.
Highlights dangers and necessary precautions for safe installation.
Specifies that installation is for RVs only and lists key prohibitions.
Guidelines for choosing a suitable installation location and clearances.
Instructions for connecting the LP gas supply, fittings, and pressure.
Guidance on connecting water inlet/outlet lines, pressure, and flow rates.
Instructions for connecting the 12V DC power supply and wire gauge selection.
Steps for installing the wall-mounted remote control.
Procedures for placing and securing the water heater unit into its opening.
Connecting power, control wires, and water lines.
Applying sealant for watertight integrity around the flange.
Method for checking gas connections for leaks using detection fluid.
Method for checking water connections for leaks after system fill.
Step-by-step guide for first-time operation and testing.
Instructions for preparing the water heater for storage or transit.
Explains the automated warming system for cold weather use.
General cautions and instructions for winterizing the appliance.
Methods for winterizing using antifreeze or compressed air.
Steps for preparing the unit for the next season.
Items to inspect yearly or before each season for proper function.
Checking air inlets and exhaust for obstructions.
Inspecting housing, wiring, safety valve, and filter.
Recommendations for treating hard water to prevent appliance damage.
Introduction to error codes and the procedure for addressing malfunctions.
Possible causes and solutions for temperature sensor, ignition, and false flame errors.
Possible causes and solutions for thermostat, fan, overheat, and pressure errors.
Possible causes and solutions for gas valve, air pressure, and flame sensor errors.
Explains timeout function and cold weather anti-freeze operations.
Addresses issues like closed valves, interrupted supply, or open faucets.
Solutions for temperature not increasing, slightly open faucets, or delayed hot water.
Explains normal conditions like white/cloudy water and fan operation.
Details compliance standards, certifications, and model information.
Instructions for checking the relief valve and electrical connection details.
Safety warnings regarding operation, temperature, and electrical hazards.
Reinforces warnings about hot water, flue pipe, electrical safety, and child operation.
Outlines the product warranty coverage period and conditions.
Details how to obtain service and make warranty claims, including required notices.
Lists items not covered by warranty and legal limitations.
Specifies the governing law and jurisdiction for disputes.
Emphasizes the importance of registering the product for warranty coverage.
General| Brand | RVMP |
|---|---|
| Model | flexTEMP FG-SBMC-11 |
| Category | Water Heater |
| Language | English |
To Next Page