Ryobi P29014 - User Manual

To Next Page

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

18 VOLT BUG ZAPPER

LANTERNE POUR INSECTES DE 18 V

EXTERMINADOR DE INSECTOS DE 18 V

P29014

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

TABLE OF CONTENTS

 Important Safety Instructions .......... 2-3

 Symbols ..............................................3

 Assembly ............................................4

 Features ..............................................4

 Operation ........................................ 4-5

 Maintenance .......................................6

 Parts Ordering/Service ........ Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

TABLE DES MATIÈRES

 Instructions de sécurité

importantes ..................................... 2-3

 Symboles ............................................3

 Assemblage ........................................4

 Caractéristiques ..................................4

 Utilisation ........................................ 4-5

 Entretien ..............................................6

 Commande de pièces /

réparation .......................... Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

ÍNDICE DE CONTENIDO

 Instrucciones de seguridad

importantes ..................................... 2-3

 Símbolos .............................................3

 Armado ...............................................4

 Características ....................................4

 Funcionamiento .............................. 4-5

 Mantenimiento ....................................6

 Pedidos de piezas/

servicio ........................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

Need help?

Do you have a question about the Ryobi P29014 and is the answer not in the manual?

Overview

RYOBI 18V Bug Zapper (P29014)
RYOBI 18V Brushless Compact Blower (PSBLB01)

This document describes two devices: the RYOBI 18V Bug Zapper (P29014) and the RYOBI 18V Brushless Compact Blower (PSBLB01).

RYOBI 18V Bug Zapper (P29014)

Function Description

The RYOBI 18V Bug Zapper is a portable lantern designed to attract and kill mosquitoes and other flying insects using UV light, while also providing area lighting. It operates on an 18V battery pack and is suitable for outdoor use. The device features a bug tray for collecting dead insects, which can be easily removed and emptied.

Important Technical Specifications

Grid Voltage: 2550 V
UV LED Light: 10.6 Watts
Area Light Lumens: 9 (low), 18 (medium), and 30 (high)
Power Source: 18V battery pack (Li-ion)

Usage Features

The bug zapper offers independent control for its UV light and area light functions.

Handle Attachment: The handle (D) is attached by looping its unattached end around the top of the bug zapper, inserting the round tab through the wide end of the hole (B) in the handle, and pulling the handle down until the tab is inside the narrow end of the hole and secure (C).

Battery Installation/Removal: To install the battery pack (B), align it with the battery port (C) and push it into the product until the latches (A) snap into place. Ensure the battery pack is fully seated and secure. To remove, depress the latches on the battery pack and pull it away from the product.

Area Light Operation: The area light (B) can be used with or without the UV light. After inserting a battery pack, the area light is initially OFF. Pressing the area light button (B) cycles through High, Medium, Low, and Off settings.

UV Light Operation: The UV light (A) attracts and kills flying insects. It can be set to run for 2, 4, or 6 hours. Pressing the UV light button (A) cycles through these timer settings and Off, indicated by LED indicators (C). The UV light and area light functions are independent.

Operating Tips:

For best results, hang the product 6 to 7 ft. above the ground.
Dead insects and debris accumulate in the bug tray (E). The bug tray should be removed and emptied frequently. To clean, pull it away, dump the waste, and use a damp cloth if necessary. Wash hands thoroughly after handling.
The product can withstand moderate rainfall but should be stored indoors during severe weather.

Maintenance Features

General Maintenance:

Avoid using solvents on plastic parts. Use clean cloths to remove dirt, dust, oil, and grease.
Do not allow brake fluids, gasoline, petroleum-based products, or penetrating oils to contact plastic parts, as these can cause damage.
Periodically remove the battery pack and use a soft brush or forced air to remove dead insects or debris from the product.
Inspect the entire product for damaged, missing, or loose parts (screws, nuts, bolts, caps). Tighten all fasteners and replace any damaged or missing parts before use.

Light Bulb Replacement: To replace the light bulb (B):

Remove the battery pack.
Twist the upper housing (A) counterclockwise to loosen it.
Remove the upper housing from the base (C).
Remove the old light bulb and replace it with an identical replacement bulb (part number 099244001022).
Attach the upper housing to the base and turn it clockwise to tighten.

Storage:

Clean all foreign material from the bug zapper.
Store indoors in a dry, locked-up place, out of reach of children.
Keep away from corrosive agents like garden chemicals and de-icing salts.

RYOBI 18V Brushless Compact Blower (PSBLB01)

Function Description

The RYOBI 18V Brushless Compact Blower is a cordless tool designed for clearing light debris from various surfaces. It utilizes an 18V battery pack and a brushless motor for optimized power and runtime. The blower can be used with or without attachment nozzles and features a lock-on button for continuous operation.

Important Technical Specifications

Motor: 18 Volts DC
Air Velocity (MPH): 140
Air Volume (CFM): 220
Power Source: 18V battery pack (Li-ion)

Usage Features

The blower is designed for ease of use and versatility in clearing tasks.

Blower Tube and Nozzle Installation/Uninstallation:

The blower tube (A) and attachment nozzles (E, G) can be installed without tools.
Tabs inside the blower tubes and nozzles fit into slots on the blower housing (B) and other blower tubes.
To install, align the arrows on the desired nozzle or blower tube and push them together. Twist until the arrow aligns with the lock icon (D) to secure.
To uninstall, twist the tube or nozzle until the arrow aligns with the unlock icon (E) and pull away.
The tool can be operated with or without the blower tube and/or nozzle attachments.

Battery Installation/Removal:

To install the battery pack (A), insert it into the battery port (B) until the latches (C) snap into place, ensuring it is fully seated and secure.
To remove, depress the latches on the battery pack and pull it from the blower.

Starting/Stopping the Blower:

To start, depress the variable speed trigger (A).
To stop, release the trigger.

Lock-On Button (B) Operation:

For continuous use, depress the switch trigger, then push in and hold the lock-on button on the side of the handle. Release the switch trigger, then release the lock-on button.
To disengage the lock, depress and release the switch trigger.

Operating the Blower:

To avoid scattering debris, blow around the outer edges of a pile, not directly into the center.
Limit the number of equipment pieces used at one time to reduce sound levels.
Be mindful of children, pets, or open windows, and blow debris safely away.
Clean up and dispose of debris properly after use.

Nozzles:

Wide Nozzle (E): Helps disperse airflow.
Speed Tip (G): Increases air velocity during operation.
Rubberized Attachment Nozzles: Help prevent scratching or marring of delicate surfaces.

Maintenance Features

General Maintenance:

Always remove the battery pack before cleaning or performing maintenance to prevent accidental starting.
Avoid using solvents on plastic parts. Use clean cloths to remove dirt, dust, oil, and grease.
Do not allow brake fluids, gasoline, petroleum-based products, or penetrating oils to contact plastic parts, as these can cause damage.
Inspect the entire product periodically for damaged, missing, or loose parts (screws, nuts, bolts, caps). Tighten all fasteners and replace any damaged or missing parts before use.
Never use water or other liquids to clean or rinse the product, and avoid exposing it to rain or wet conditions. Store indoors in a dry area.

Storage: