Need help?Do you have a question about the S-BOL RFC-696 and is the answer not in the manual?
This document provides an operation manual for a professional hair clipper, model RFC-696, designed for professional use. It details the components, parameters, usage instructions, and maintenance procedures for the device.
The hair clipper is a versatile grooming tool designed for precise hair cutting and trimming. It operates in a rechargeable mode, offering both corded and cordless functionality for convenience and flexibility during use. The device is equipped with a high-performance motor and is designed to be waterproof, allowing for easy cleaning and maintenance.
The clipper features a comprehensive set of components to facilitate various cutting styles and lengths. It includes a bottom blade, a top blade, and a blade lever for adjusting the cutting position. The ON/OFF switch controls the device's power. For charging, a universal voltage charger is provided, allowing the clipper to be powered from a standard USB connection.
A key feature of this clipper is its extensive range of limit combs, which enable precise length adjustments. The manual illustrates ten different limit comb sizes: 1.5mm, 3mm, 4.5mm, 6mm, 10mm, 13mm, 16mm, 19mm, 22mm, and 25mm. These combs are designed for cropped hair and hair trimming, offering a wide array of length options to suit different styling needs. To mount a limit comb, users align it with the blade edge and push it slightly forward until it clicks into place. Disassembly is achieved by pulling the comb hard.
The clipper also incorporates a fine-tuning mechanism for the cutter. This allows users to adjust the cutter by rotating an adjusting ring from forward to downward, providing even greater control over the cutting length and precision.
The device supports a travel lock function, which can be activated by pressing the power button for 5 seconds to lock the machine, and similarly, pressing it for 5 seconds again to unlock it. This feature prevents accidental activation during travel or storage.
To use the rechargeable mode, the charger is inserted into the tail of the clipper and connected to a power source. The charging indicator light will illuminate to show that charging has commenced. Once the indicator displays "100," the device is fully charged. The clipper can be used both while charging (corded) and when fully charged (cordless).
The manual provides detailed instructions for cutter assembly and disassembly, emphasizing the importance of proper blade alignment for optimal performance and safety. When assembling, the end of the top blade teeth should be positioned slightly back from the bottom blade (approximately 0.79mm to 1.98mm). This prevents the clipper from cutting too close or allowing the moving cutter to touch the skin. Additionally, the extreme left-hand tooth of the top blade must cover or be to the left of the first small tooth of the bottom blade, and the extreme right-hand tooth of the top blade must touch the big tooth on the bottom blade.
Some clippers are equipped with an adjustable taper lever, which allows users to change the closeness of the cut. When the lever is in the uppermost position, the blades provide the closest cut. Pushing the lever downward gradually increases the cutting length, offering seamless blending and fading capabilities.
Maintaining the hair clipper is crucial for its longevity and performance. The manual outlines specific procedures for blade alignment, cleaning, and oiling.
The clippers are carefully examined and aligned at the factory. However, if the blades are removed for cleaning or replacement, realignment is necessary. To realign, users should match the upper and bottom blade teeth point for point, ensuring the end of the top blade teeth is approximately 0.5-1.0mm back from the bottom blade. If alignment is incorrect, a few drops of oil should be applied to the blade, the clipper turned on briefly, then turned off and unplugged. The screws can then be slightly loosened, the blades adjusted, and the screws tightened.
Regular oiling is recommended to keep the clipper in peak condition. The blades should be oiled every few haircuts. To oil properly, the unit should be held with the blades in a downward position, and 2-3 drops of oil dispensed across the top blade while the clipper blade is running.
The clipper is waterproof (IPX7), allowing for easy cleaning. It can be placed into water or rinsed under running water. After cleaning, it should be wiped dry with a soft cloth. For better storage and continued performance, a few drops of lubricating oil should be added to the blade, and the appliance restarted briefly.
Users are advised not to disassemble the product. Charging should not occur in environments above 40°C or below 0°C. While using or charging, the product may produce a little heat, which is considered normal. When the battery runs out, it should be removed safely and returned to specified collection points, not discarded casually. After water washing, if not for immediate use, the product should be placed at a certain angle for several hours to allow any water inside to flow out. If the machine is not used immediately, two drops of lubricating oil should be applied to the cutter head for maintenance.
The manual also includes information regarding the Waste Electrical and Electronic Equipment (WEEE) Directive and battery disposal, emphasizing environmentally responsible practices.
General| Blade Material | Stainless Steel |
|---|---|
| Battery Type | Lithium-Ion |
| Run Time | 90 minutes |
| Adjustable Cutting Lengths | Yes |
| Comb Sizes | 3mm, 6mm, 9mm, 12mm |
| Display | No |
To Next Page