Safe Fleet NH16v2 User Manual

© Safe Fleet | 2023 Part #: 700-1299 R2
NH16v2 NVR System Quick Installation Guide
Typical System Setup: The NH16v2 supports a maximum of 16 channels (12 channels without the network switch):
Optionally connect... To...
PoE Injector Kit ACC PWR
RGY Button*
2
Adapter Harness (1x5
Microt Connector)
Smart-Reach (Wi-Fi)*
3
WIFI Input
Smart-Reach Cellular Modem*
3
MODEM Input
Laptop LAN Input (front)
Portable Video Monitor*
4
VIDEO OUT (front)
External G-Sensor G-SENSOR Input
Alarm Switch ALARM 2 Input
SD Card*
5
SD Card Slot (front)
1. Vehicle speed and location tracking require the GPS antenna
(part # ANT-G6-SM, 19.6ft/6m cable).
2. The RGY Button is optional, and requires the WT2 adapter
harness and the RGY extension harness (part# 060-1197).
3. An optional Smart-Reach Wi-Fi bridge or Smart-Reach Cellular
modem can be connected to the rear panel WIFI/MODEM ports.
4. An optional Video Monitor can be used from the video output
located on the front panel.
5. Use Safe Fleet-approved cards only.
6. Wake/Signal 6 input, active high (5-32V edge-triggered).
Notes (*)
Black - Battery Negative
Yellow - Vehicle Ign +12V
Red - Vehicle +12V
This Quick Installation Guide is a basic install and setup reference for the recorder. Review it completely before proceeding. The NS18POE16
network switch is compatible with NH16v2. Third-party switch gear is not supported. Refer to the 16-Port Network Switch Installation Guide,
(part #700-1156) for more information. Information is subject to change without notice. Please visit the Safe Fleet Community at
https://community.safeeet.net for the latest product details and full installation instructions.
Harness WT2 sup-
ports RGY button
and extn. harness
pkg. HEDM20
POWER
20 ft./6.1m
Power harness: 060-1136
Power harness/fuse pkg.:
PH1X3UM20
060-1059
Expansion
Harness:
G-SENSORALARM2
ACC PWR
CAMERAS/ALARMS
MODEM
USB
GPS
WIFI
POE01
POE02G
POE04
POE03
16 IP Cameras from the
NS18POE16 Network Switch
8 Std. Resolution and/or High Denition Cameras
Adapter
Harness*
2
5 wires
RGY BUTTON 065-1010
(Optional)
1x5 Microt
3 wires
1A
20A
Rear Vision System (Optional)
Reserved
2x3 Microt
1x4 Microt
2 wires
WAKE (Optional)
Green - Input: Wake/Signal 6*
6
Black - Battery Negative
SIGNALS
S01 - Black
S02 - Green
S03 - Red
S04 - Brown
S05 - White
2 wires
DIGITAL OUTPUT (Optional)
Blue - Active H (12V 150mA source)/
Active L (ground 350mA sink)
Black - Ground
20 ft./6.1m RGY extn.
harness: 060-1197
 WARNING: Cable and harness slack
Ensure cables and harnesses have slack and can move
freely with the recorder without being pulled to the side
or away from the connector. A 4-inch diameter loop is
normally sucient.
 WARNING: Noise suppression
Do not use the output of a noise suppression solenoid
as a recorder ignition or power source. If no true ignition
or power source can be readily found, consult the bus
schematic bus or manufacturer to locate a proper source.
 WARNING: Automatic drive formatting
Storage media might not be recognized on recorders running
different rmware. By design, unrecognized media automatically
formats when inserted into a recorder, so recording can
commence. Customers who swap cartridges between recorders
should ensure each recorder has the same rmware version.
Network Switch
Control Cable
060-0656
Video Breakout Harness:
VBH-8D-2SA-M
Alarm Input (ALM C)
Signal Input (SIG)
Purple - Signal 7
Blue - Signal 8
2-conductor
1x2 Microt
Antenna*
1
4 IP Cameras (if Network
Switch not installed)
ANT-G6-SM
GPS RF
Information is subject to change without notice.
Please visit the Safe Safe Fleet Community at https://community.safeeet.net for the latest product details and full installation instructions.
Warranty and Support
For full warranty information, visit www.seon.com/documents/Seon-Warranty.pdf Technical Support phone - 1.844.899.7366
Email - PTsupport@safeeet.net
Basic NVR conguration (continued)
Step 7. System
Password Enable: Leave OFF unless instructed
otherwise.
Password: If enabled, this password is required for non-
Admin users to access the local NVR UI.
Audio Output Channel: Select the audio channel that will
be available from the audio RCA port on the front of the
NVR.
Diagnostic Indicator: If installing an RGY Button or RGY
Illuminator, select which one.
Language: Select the language for the NVR UI.
Scheduled Reboot/Reboot Now: Congure a time-of-day
for the recorder to reboot, or reboot immediately.
Click Program Update.
Step 8. Load Cong File, Format Drive
Store Current Conguration: Select USB Device as the le-saving destination. Plug a USB
memory device into the front of the NVR. Click Store to save the le on the USB memory device.
Load: For details on uploading congurations to the recorder, see “NVR Conguration Uploads”
in the NH16v2 Installation and Conguration Guide.
Update: Delivers a rmware update to the recorder or a connected IP camera from an image le
stored on a USB device. Select DVR or IPC, then click Update and navigate to the image le:
DVR: The device reboots when updates are done.
IPC: Click a numbered tab at the top of the screen to update rmware on the camera
connected to the selected port, then click Update.
Format: Format the hard drive and SD card (if installed) when the conguration is complete and
tested and before nal delivery of the installation to the customer.
Click Back twice to save settings and return to the Conguration menus.
Advanced Conguration Options
Alarms & I/OSignals: congure signal inputs and the actions they generate.
Alarms & I/OSpeed: record vehicle speed or trigger notications for excessive speed.
NetworkUser Levels: create NVR user logon proles and assign passwords to enable remote access with various permission levels.
For more information about these settings, please see the NH16v2 Installation and Conguration Guide (700-1300) on the Safe Fleet Community Web site.
Step 5. Alarms
From the Conguration menu, select Alarms & I/OAlarms.
Alarm: Alarms 1 and 2 can be triggered by an event/alarm button. AlarmC
is triggered from a hardware input (ALM C on the Video breakout harness).
Alarms 1-4 can also come from Signals or features such as speed or GPS.
Pre Alarm: Optionally, select a time period prior to an alarm being triggered
where recorded video and metadata are included with protected alarm data,
which won’t be overwritten. For more information, see Recording Settings
(Advanced) in the NH16v2Install and Cong Guide.
Duration: Set the Duration for how long the NVR will record video agged as
an alarm for each alarm input.
Input: Applies to Alarm1, Alarm2, and AlarmC only. Choose N.O. (Normally
Open), N.C. (Normally Closed), or N.H. (Normally High) depending on the
switch type used.
Speed (frames/second), Quality, and Resolution: For each alarm, select
higher settings for better video while the alarm is recording.
Important: If Encode Perf. is below 0, adjust Speed, Quality, or Resolution
settings until the value is at or above 0. Note that Speed, Quality, and
Resolution settings are only adjustable for specic camera/device
types. For details, see the NH16v2 Install and Cong Guide.
Audio: When audio is normally disabled, set ON to enable audio for the Alarm
Duration period.
Click Back twice to save settings and return to the Conguration menu, then
click Network.
Step 6. Network
From the Conguration menu, select Network  IP Addresses  Front.
Setting Type: Leave at default Static IP setting.
IP address: used to communicate with the NVR over the network via a
laptop for installation and conguration purposes. Leave at default setting
unless instructed by the customer.
HTTP Port: typically, leave set to 80 unless instructed by IT personnel.
Notes:
If Smart-Reach Mobile Wi-Fi equipment or a Smart-Reach Cellular
modem is installed, click Network  IP Addresses  Wi/Modem to
congure communication parameters. For more information, see the
NH16v2Install and Cong Guide and the Smart-Reach documentation
available on the Safe Fleet Community.
If the IP information is changed and saved in a conguration le
for upload to other NVRs, their settings will have to be updated as
well. For more information, see “NVR Conguration Uploads” in the
NH16v2Install and Cong Guide.
If the system uses Commander or Depot Manager: contact Technical
Support for assistance with setup.
Click Back to save settings and return to the Conguration menu, then
click System.

Safe Fleet NH16v2 Specifications

General

Brand	Safe Fleet
Model	NH16v2
Category	Measuring Instruments
Language	English