To Next PageTo Next Page
Need help?Do you have a question about the Safran RX-1 and is the answer not in the manual?
Explains safety warnings and symbols used in the manual.
General precautions for safe installation and operation.
Covers cleaning, chassis, power sources, and cord protection for safe operation.
Details grounding, power supply, and battery safety guidelines.
Information on FCC rules, CE marking, and WEEE directive for compliance.
Safety statements provided in multiple languages for international users.
Describes the purpose and scope of the user's manual for the RX-1 receiver.
Lists documents relevant to the RX-1 technical specifications and standards.
Lists other documents related to quality assurance.
Glossary of terms, symbols, prefixes, and abbreviations used in the manual.
Overview of the RX-1 Compact Operational Receiver's capabilities and features.
Details the core specifications and parameters of the RX-1 receiver.
Describes optional features and their functionalities available for the RX-1.
Information on the physical dimensions and rack mounting of the RX-1.
Guidelines for integrating the RX-1 into a standard 19-inch rack.
Specifies operating and storage temperature ranges and cooling recommendations.
Details the electrical interconnections and back panel layout of the RX-1.
Step-by-step guide for installing the operating system on the RX-1.
Instructions for preparing an SD card for software upgrades.
Procedure for performing software upgrades on the RX-1 receiver.
Overview of the RX-1's front panel interface and controls.
Provides quick access to main operational parameters like Frequency, Combiner, IF Filter, Mode, and Bit Rate.
Access to sub-menus for configuring system parameters.
Explains the function of the ALARM, REMOTE, and SYSTEM status LEDs.
Overview of the Main and Configuration menus and parameter navigation.
Summarizes allowed modulation configurations for independent channels.
Explains the function and settings of the Pre D combiner.
Describes the zeroing function for balancing RF gain and its prerequisites.
Details the Automatic Frequency Control feature for FM and PCM-FM modes.
How to perform noise figure measurements using the receiver's AGC configuration.
Guidance on using the Post-D combiner for frequency diversity in FM mode.
Setup for using the internal Post-D combiner without external cabling.
Interconnection and setup for external Post-D combining.
Explanation of the equalizer's function for signal distortion mitigation.
Information on supported demodulation types and FM discriminator gain adjustment.
Details on Forward Error Correction methods like Convolutional, Reed Solomon, Turbo, and LDPC.
Explanation of DQE and DQM for output frame quality information.
Describes the process of identifying telemetry frames and synchronization word.
Configuration and management of telemetry data storage.
State machine diagram for COFDM synchronization.
Specifies the location of the XML configuration files.
Describes the structure and tags within the XML configuration file.
Registry parameters for time code configuration and date formats.
Registry settings for TM server UDP protocol configuration.
Registry parameters for configuring 35MHz spurious rejection.
Registry settings for extra commands like reset and shutdown.
Registry settings for RS FEC frame setup.
Registry settings for RS FEC (Soyuz) frame setup.
Registry settings for TPC FEC frame setup.
Registry parameters for IRIG-B time processing and system updates.
Registry settings for viewer server activation and port configuration.
Registry settings for telemetry data storage file size and path.
Registry settings for MCS TCP interface and auto-reconnection.
Details specific alarms related to ADP3 hardware and functionality.
Lists alarms associated with tuner and multiband functionalities.
Explains safety warnings and symbols used in the manual.
General precautions for safe installation and operation.
Covers cleaning, chassis, power sources, and cord protection for safe operation.
Details grounding, power supply, and battery safety guidelines.
Information on FCC rules, CE marking, and WEEE directive for compliance.
Safety statements provided in multiple languages for international users.
Describes the purpose and scope of the user's manual for the RX-1 receiver.
Lists documents relevant to the RX-1 technical specifications and standards.
Lists other documents related to quality assurance.
Glossary of terms, symbols, prefixes, and abbreviations used in the manual.
Overview of the RX-1 Compact Operational Receiver's capabilities and features.
Details the core specifications and parameters of the RX-1 receiver.
Describes optional features and their functionalities available for the RX-1.
Information on the physical dimensions and rack mounting of the RX-1.
Guidelines for integrating the RX-1 into a standard 19-inch rack.
Specifies operating and storage temperature ranges and cooling recommendations.
Details the electrical interconnections and back panel layout of the RX-1.
Step-by-step guide for installing the operating system on the RX-1.
Instructions for preparing an SD card for software upgrades.
Procedure for performing software upgrades on the RX-1 receiver.
Overview of the RX-1's front panel interface and controls.
Provides quick access to main operational parameters like Frequency, Combiner, IF Filter, Mode, and Bit Rate.
Access to sub-menus for configuring system parameters.
Explains the function of the ALARM, REMOTE, and SYSTEM status LEDs.
Overview of the Main and Configuration menus and parameter navigation.
Summarizes allowed modulation configurations for independent channels.
Explains the function and settings of the Pre D combiner.
Describes the zeroing function for balancing RF gain and its prerequisites.
Details the Automatic Frequency Control feature for FM and PCM-FM modes.
How to perform noise figure measurements using the receiver's AGC configuration.
Guidance on using the Post-D combiner for frequency diversity in FM mode.
Setup for using the internal Post-D combiner without external cabling.
Interconnection and setup for external Post-D combining.
Explanation of the equalizer's function for signal distortion mitigation.
Information on supported demodulation types and FM discriminator gain adjustment.
Details on Forward Error Correction methods like Convolutional, Reed Solomon, Turbo, and LDPC.
Explanation of DQE and DQM for output frame quality information.
Describes the process of identifying telemetry frames and synchronization word.
Configuration and management of telemetry data storage.
State machine diagram for COFDM synchronization.
Specifies the location of the XML configuration files.
Describes the structure and tags within the XML configuration file.
Registry parameters for time code configuration and date formats.
Registry settings for TM server UDP protocol configuration.
Registry parameters for configuring 35MHz spurious rejection.
Registry settings for extra commands like reset and shutdown.
Registry settings for RS FEC frame setup.
Registry settings for RS FEC (Soyuz) frame setup.
Registry settings for TPC FEC frame setup.
Registry parameters for IRIG-B time processing and system updates.
Registry settings for viewer server activation and port configuration.
Registry settings for telemetry data storage file size and path.
Registry settings for MCS TCP interface and auto-reconnection.
Details specific alarms related to ADP3 hardware and functionality.
Lists alarms associated with tuner and multiband functionalities.
General
