5. Operation
2/2
** This product must be installed by a licensed electrician
5.1 Button operation
Single click: Trigger the corresponding channel gate/door to open/pause/close,
depending on its previous status.
4 clicks: The device enters pairing mode, the LED indicator quickly flashes in blue
and white for 30 seconds. This is for pairing the corresponding channel control to
a PIXIE secondary device, so the gate/door can be controlled by an extra
device, typically a physical button on the wall for convenient control.
9 clicks: Reset the PIXIE Gate & Door Control to factory default. The LED indicators
flash in blue and white for 3 seconds then stay at white.
5.2 The LED indicators
-The LED indicators are solid white colour when the device is new or factory
reset, and are solid blue when the device is added into the App.
-Each LED indicator stays at low light when the corresponding channel reed
switch contact is open (typically meaning the gate/door is open), and
becomes high light when the reed switch contact is closed (typically meaning
the gate/door is closed).
NSW | ACT
QLD
VICT | TAS | SA | NT
WA
SAL National Pty Ltd, 40 Biloela Street Villawood NSW 2163
SAL National Pty Ltd, 36 Whitelaw Place Richlands QLD 4077
SAL National Pty Ltd, 46-48 Keys Road Moorabbin Victoria 3189
SAL National Pty Ltd, 29 Beringarra Av Malaga WA 6090
| P # 02 9723 3099
| P # 07 3879 5999
| P # 03 9532 3168
| P # 08 9248 7458
8. Scan QR code to access the full product information
7. Warranty
In accordance with SAL’s standard terms and conditions of sale, SAL warrant this product to be free from defects in materials and or workmanship for a period as
stated below for goods not subject to incorrect installation, maintenance, operation, mishandling, environmental, unauthorised modifications or electrical
operating conditions outside the nominated product specification as detailed in these installation instructions.
The benefits to you given by this warranty are in addition to other rights and remedies you have under law. Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Warranty term – Residential usage (12) months, Commercial usage (12) months
7.1 How to make a claim?
Step #1 – Within 30 days of the fault discovery, please contact the original place of the SAL product purchase during standard (local) business hours, with the
following information (a) proof of purchase (b) description and quantity of the claimed fault (c) address of installation. (d) operating hours of the product.
Step #2 – It is then the responsibility of the original place of product purchase to report the matter to SAL aftersales;
Step #3 - Upon review of your claim and if the product is required to be returned to SAL for technical evaluation, then at the owners expense the product must
be returned to SAL as per the above nominated locations.
Step #4 - Pending the evaluation, the claim will be validated resulting in the product being repaired or replaced with the same or best equivalent product at
the discretion of SAL, or rejected if the product fault was found to be caused by conditions beyond the responsibility of SAL warranty obligations. Consideration
of installation, product removal, return freight and or testing fees are not the responsibility of SAL.
6. How to download App
Scan QR code or go to App store (IOS) or Google Play (Android) to
download the free PIXIE or PIXIE PLUS app to your smart phone.
IOS: Requires IOS 6.0 or later. Compatible with iPhone, iPad and
iPod touch
Android: Requires Android 4.4 or above, devices must support
Bluetooth 4.0 or above
Specifications above are for reference only and may vary without
prior notice.
2. Make sure the Mode DIP switch set to “1”
3. Add this device into PIXIE or PIXIE PLUS App, follow the step-by-step guide in the App to finalise the configuration
To Previous Page
Loading...