SAL PIXIE - User Manual

Model NO.
Operation Ambience
Temperature (ÝC)
Output
IP Rating
Storage Ambience
Temperature (ÝC)
Storage Humidity Role in PIXIE System
Attachments
PC206GD/R/BTAM 240V~ 50Hz
0 ~ 40
Dry contact signals
IP20
0 ~ 60
10% - 85% RH, NC
10% - 85% RH, NC
Contact sensor (sold separately)
Master
Operation Humidity
Input
SAL products are designed in accordance with all mandatory International and Australian Standards, which require installation in accordance with
AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equipment. Products are sold in accordance with the following
instructions and SAL standard terms and conditions of sale, available via www.sal.net.au.
Due to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performance
guarantee unless expressly confirmed in writing by SAL at the time of order. The product wireframe drawings in this document are intended for illustration purposes
only and may differ from the final physical product. The installation instruction is subject to change without prior notice.
MASTER
1. Foreword
IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE GUIDE AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
2. Product Introduction
The PIXIE Gate & Door Control is designed to control motorised sliding gates, swing
gates and garage doors which accept single dry contact signal (such as bell press,
voltage free signal, dry-contact etc) as a command input. It’s capable of monitoring
the open/closed status via a set of contact sensor (sold separately), and sending status
change notifications to the user as required via PIXIE PLUS App only. Once properly
configured in the PIXIE Plus App, users are provided visual feedback demonstrating the
current status and in some instances, position of the controlled appliance.
2.1 Product Features
• Control 1 sliding gate, or 1 swing gate, or up to 2 garage doors
• Works with wired contact sensors (magnetic reed switches) for different gates and
doors, providing monitoring of open/closed status
• Two in-built buttons for easy setting and testing
• Two LED indicators to reflect the contact sensor’s position status
2.2 The package includes
• PIXIE Gate & Door Control * 1
• Quick Start Guide *1
4. Installation and Wiring
4.1 Preparation
-Select suitable contact sensor (NC type), which comes as a pair,
consisting of a reed switch and a magnet. The reed switch contact
is closed when the magnet is present, and the contact opens when
the magnet moves away.
-The reed switch comes with cable attached and is supposed to be
mounted on a fixed surface, e.g. the ground, the wall, or a pole
etc. The magnet is supposed to be mounted on a moving part,
typically the gate/door.
-Make sure the reed switch contact is closed when the gate/door is
closed, and the contact is open when the gate/door is open.
4.2 Installation**
1. Wire the PIXIE Gate & Door Control as per the wiring diagram on
the right
2.3 Product illustration*
3. Specifications
DIY
SAL products are designed in accordance with all mandatory International
or
d
: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE
PC206GD/R/BTAM
PIXIE Gate & Door Control
Quick Start Guide
Version
Date 08/01/2024
1.2
1/2
*All drawings shown are for illustration purpose
only, actual product may vary due to product
enhancement.
MASTER
110 mm
26 mm
LED Indicators
DIP switch for Mode selection
Select 1 for most applications
Power Input
(240V~50Hz)
Terminals of
CH2 output
Terminals of
CH1 output
Contact Sensor
Input
CH1 and CH2 buttons
40 mm
Wiring diagram
A
N
Contact sensor 2
(Optional)
(Optional)
(Must)
(Must)
Contact sensor 1
Garage Door 2 motor
Gate/Door 1 motor
signal input terminals
signal input terminals
S2
CH2
1 2
Mode
CH1
CH2
2B2A1B1A
CH1
A N C S1

Summary

Product Introduction

Product Features

Lists key features like controlling gates/doors, using contact sensors, and LED indicators.

Product Illustration

Illustrates the physical layout and components of the PIXIE Gate & Door Control.

Specifications

Installation and Wiring

Preparation

Details selecting NC type contact sensors and their mounting on moving/fixed parts.

Installation

Instructs to wire the PIXIE Gate & Door Control using the provided diagram.

Operation

Button Operation

Explains how single clicks, 4 clicks, and 9 clicks affect the device's operation and status.

LED Indicators

Describes LED colors and states indicating device status, pairing, and sensor feedback.

Warranty

How to Make a Claim

Outlines the steps for making a warranty claim, including contact details and required information.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The PIXIE Gate & Door Control (Model PC206GD/R/BTAM) is a smart device designed to integrate motorized sliding gates, swing gates, and garage doors into the PIXIE smart home ecosystem. It acts as a master device within the PIXIE system, enabling control and monitoring of these access points through the PIXIE PLUS App.

Function Description:

The primary function of the PIXIE Gate & Door Control is to receive single dry contact signals (such as bell press or voltage-free signals) as command inputs for operating gates and garage doors. It can control one sliding gate, one swing gate, or up to two garage doors. A key feature is its ability to monitor the open/closed status of these access points using wired contact sensors (magnetic reed switches), which are sold separately. This status information is then sent as notifications to the user via the PIXIE PLUS App, providing visual feedback on the current state and, in some cases, the position of the controlled appliance. The device also supports pairing with PIXIE secondary devices, allowing for control via additional physical buttons.

Important Technical Specifications:

• Model No.: PC206GD/R/BTAM
• Input: 240V~50Hz
• Output: Dry contact signals
• Operation Ambience Temperature: 0 ~ 40°C
• Storage Ambience Temperature: 0 ~ 60°C
• Operation Humidity: 10% - 85% RH, NC
• Storage Humidity: 10% - 85% RH, NC
• IP Rating: IP20
• Role in PIXIE System: Master
• Dimensions: Approximately 110 mm (length) x 40 mm (width) x 26 mm (height).

Usage Features:

• Control Capabilities: Controls one sliding gate, one swing gate, or up to two garage doors.
• Contact Sensor Integration: Works with wired contact sensors (magnetic reed switches) to monitor open/closed status. These sensors consist of a reed switch and a magnet. The reed switch contact is closed when the magnet is present (gate/door closed) and opens when the magnet moves away (gate/door open).
• App Integration: Fully configurable and controllable via the PIXIE PLUS App (available on iOS and Android). The app provides visual feedback on the current status and position of the controlled appliance.
• On-device Buttons: Features two in-built buttons (CH1 and CH2) for easy setting and testing of the corresponding channels.
• LED Indicators: Two LED indicators provide visual feedback on the device's status and the contact sensor's position.
  • Solid white: New device or factory reset.
  • Solid blue: Device added to the App.
  • Low light: Corresponding channel reed switch contact is open (gate/door open).
  • High light: Corresponding channel reed switch contact is closed (gate/door closed).
• DIP Switch: A DIP switch is available for mode selection, with "1" being the setting for most applications.
• Button Operations:
  • Single click: Triggers the corresponding channel gate/door to open/pause/close, depending on its previous status.
  • 4 clicks: Enters pairing mode (LED indicator flashes blue and white for 30 seconds) for pairing with a PIXIE secondary device, allowing control from an additional physical button.
  • 9 clicks: Resets the device to factory default (LED indicators flash blue and white for 3 seconds, then stay white).
• Installation: Requires installation by a licensed electrician. The device is wired to the 240V~50Hz power input and connects to the gate/door motor signal input terminals (dry contact signals) and contact sensors. Contact sensor 1 is mandatory, while contact sensor 2 is optional for controlling a second gate/door.
• App Download: The PIXIE and PIXIE PLUS apps can be downloaded from the App Store (iOS 6.0 or later) or Google Play (Android 4.4 or above, with Bluetooth 4.0 support).

Maintenance Features:

• Warranty: SAL provides a warranty against defects in materials and workmanship for 12 months for residential usage and 12 months for commercial usage, provided the product is installed, maintained, and operated correctly according to the instructions.
• Claim Process: To make a warranty claim, contact the original place of purchase within 30 days of fault discovery, providing proof of purchase, description of the fault, installation address, and operating hours. The product may need to be returned to SAL for technical evaluation at the owner's expense.
• Cleaning and Maintenance: Regular cleaning and maintenance of the equipment are required as per AS/NZS3000 standards.

The PIXIE Gate & Door Control is designed to offer a robust and integrated solution for automating and monitoring access points, enhancing convenience and security through smart home technology.

SAL PIXIE Specifications

General

Brand	SAL
Model	PIXIE
Category	Door Opening System
Language	English