EasyManua.ls Logo

Salt Dogg SHPE2000 User Manual

Salt Dogg SHPE2000
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • saltdogg.com
Installation Instructions
—continued inside
SHPE2000, SHPE2000RED, SHPE2000YEL
Series SaltDogg
®
Electric Drive Poly Hopper
Spreader
2.0 cubic yards
U.S. PATENT 9,562,333
Table of Contents
General Information .....................................................................1
Safety Precautions .......................................................................1
Warranty Information ...................................................................2
Installation Instructions ............................................................ 2-4
Spreader Operation .....................................................................5
Spreader Maintenance .................................................................5
Repair Parts & Drawings .........................................................6 -10
General Information
Spreader models:
• SHPE2000- spreader with standard length chute
• SHPE2000X- spreader with extended length chute
Overall Length: 96 inches
Overall Width: 47-1/2 inches
Overall Height: (installed): 40 inches
Empty Weight:
437 lbs. (standard chute), 441 lbs. (extended chute)
Capacity Struck: 2.0 cu. yd.
Average Installation Time: 3 hrs.
Vehicle Requirements
• 3/4 or 1 ton pick-up truck above 8500# GVWR.
• 135 AMP or higher alternator is recommended.
Materials Recommended to Spread
SHPE2000 SALT DOGG SPREADER WARRANTY
INFORMATION
This warranty replaces all previous warranties and no
employee of this company is authorized to extend addi-
tional warranties, or agreements, or implications
not explicitly covered herein.
Buyers Products Company warrants all parts of the
product to be free from defects in material and workman-
ship for a period of two (2) years. Parts must be properly
installed and used under normal conditions. Normal wear
is excluded.
Any part, which has been altered, including modifica-
tions, misuse, accident, or lack of maintenance will not
be considered under this warranty.
The sole responsibility of Buyers Products Company
under this warranty is limited to repairing or replacing any
part(s), which are returned, prepaid, 30
days after such defect is discovered, and returned part(s)
are found to be defective by Buyers Products Company.
Authorization from Buyers Products Company must be
obtained before returning any part. The following infor-
mation must accompany defective parts returned
to Buyers Products Company: RMA #, spreader model,
serial number, date installed, and distributor from whom
purchased.
Buyers Products Company shall not be liable for damage
arising out of failure of any unit to operate properly, or
failure, or delay in work, or for any consequential dam-
ages. No charges for transportation or labor performed
on any part will be allowed under this warranty.
CAUTION
Do not overload vehicle beyond the vehicle’s GVWR or GAWR.
Check vehicle's load rating certification sticker for maximum
vehicle capacity.
Average Material Weights
Materials to use Weight (pounds per cubic yard)
Fine Salt-Dry 2,250
Coarse Salt-Dry 1,431
Sand/Salt up to 50/50 Mix-Dry 2,700
Note: To calculate the total spreader weight (including ice
control material), add the empty spreader weight plus the ice
control material and spreader accessories.
Question and Answer IconNeed help?

Do you have a question about the Salt Dogg SHPE2000 and is the answer not in the manual?

Salt Dogg SHPE2000 Specifications

General IconGeneral
BrandSalt Dogg
ModelSHPE2000
CategoryPower Tool
LanguageEnglish

Summary

General Information

SHPE2000 SaltDogg Spreader Warranty Information

Safety Precautions

General Safety Guidelines

Essential safety rules to prevent injury and damage during operation.

Installation Instructions

Mounting the Spreader onto the Vehicle

Steps for physically attaching the spreader to the truck bed.

Install Control Box & Vehicle Wiring Harness

Procedure for connecting the electrical control system to the vehicle.

Spreader Operation

Material Flow Adjustments

Spreader Maintenance