Why does my Samil Power SP-SR-V5-EN show a Grid Fault?
The Samil Power Inverter might display a 'Grid Fault' message while it is waiting for one minute for the grid to return to its normal working state. Also, ensure that the grid voltage and frequency comply with the required standards.
What to do if Samil Power SP-SR-V5-EN Inverter shows No Utility?
If your Samil Power Inverter displays 'No Utility', it might be off to the grid. Check the grid connection, including the wire and interface. Also, verify the grid's usability.
What to do if Samil Power SP-SR-V5-EN displays Ground I Fault?
If the Samil Power Inverter shows a 'Ground I Fault', it means the leakage current is too high. Disconnect both the DC and AC connectors and inspect the surrounding equipment on the AC side. After troubleshooting, reconnect the input connector and check the state of the inverter.
Why Samil Power SP-SR-V5-EN displays PV Over Voltage?
The Samil Power Inverter displays 'PV Over Voltage' when the panel’s open-circuit voltage is similar to or greater than the Max. DC voltage. Check the panel's open-circuit voltage to ensure it is not exceeding the maximum DC voltage.
How to fix DC INJ High error on Samil Power SP-SR-V5-EN?
The 'DC INJ High' error on your Samil Power Inverter indicates that the DC injection is higher than the set value. Wait for one minute to see if it returns to normal.
How to resolve SCI Failure on Samil Power SP-SR-V5-EN Inverter?
To resolve an 'SCI Failure' on your Samil Power Inverter, disconnect the PV (+) and PV (-) from the DC input, and then reconnect them.
What causes Isolation Fault in Samil Power SP-SR-V5-EN?
To determine the cause of an 'Isolation Fault' in your Samil Power Inverter, check the impedance among PV (+), PV (-), and ground.
How to fix Consistent Fault on Samil Power Inverter?
To fix a 'Consistent Fault' on your Samil Power Inverter, disconnect the PV (+) and PV (-) from the DC input, and then reconnect them.
How to troubleshoot Fan Fault on Samil Power SP-SR-V5-EN Inverter?
To troubleshoot a 'Fan Fault' on your Samil Power Inverter: * Check the fan to see if it is blocked. * Verify the fan's wiring to ensure it is normal.
How to resolve Relay Failure on Samil Power SP-SR-V5-EN?
To resolve a 'Relay Failure' on your Samil Power Inverter, disconnect the PV (+) and PV (-) from the DC input, and then reconnect them.
Defines the scope and applicability of this installation guide for SolarRiver Series inverters.
Specifies that the manual is intended for qualified personnel only.
Explains the safety instructions and general information symbols used throughout the document.
Describes the intended use of the SolarRiver Series inverter as a PV inverter feeding into the public grid.
Provides critical safety warnings regarding high voltages, hot surfaces, and radiation effects.
Details the meaning of various symbols found on the inverter and type label for safety and identification.
Outlines the key technological advancements, reliability, and control features of the SR Series inverter.
Presents a schematic diagram illustrating the internal electrical components and their interconnections.
Provides the physical dimensions and weight specifications for different models of the PV inverter.
Details the DC input specifications, including maximum power, voltage, and current for various inverter models.
Lists the AC output specifications such as nominal power, maximum power, current, voltage, and frequency.
Covers inverter efficiency ratings and built-in safety and protection mechanisms.
Presents miscellaneous technical data including dimensions, weight, cooling, noise, operating temperature, and warranty.
Describes the different operational states of the inverter, such as Stand-by, Checking, On-grid, MPPT, Fault, and Setting modes.
Lists the components included in the inverter's packaging and their quantities.
Outlines crucial precautions to take regarding the installation environment and site conditions.
Lists the necessary tools required for performing the installation of the inverter.
Provides a step-by-step guide for physically mounting the inverter and its bracket.
Explains how to connect the PV modules and arrays to the inverter, including voltage limitations.
Details the procedure for starting up the inverter after installation, including pre-start checks and operational states.
Describes the physical control panel of the inverter, including the LCD, LED indicators, and function key.
Explains how to use the function key to navigate and set parameters on the inverter's LCD display.
Provides a table detailing the information displayed on the LCD screen for various operating states and their descriptions.
Introduces the optional RS485/RS232 communication interfaces for monitoring inverter data.
Explains the two communication types, RS232 for single inverters and RS485 for multiple inverters.
Offers guidance and tips for identifying and resolving common problems encountered with the SolarRiver series inverters.
Provides instructions on basic maintenance procedures, focusing on cleaning the inverter and its cooling fan.
Details the steps required to safely disconnect and remove the inverter from its installation.
Provides guidelines for packing the inverter for storage or transport, either in original or equivalent packaging.
Specifies the recommended storage conditions, including temperature range, for the inverter.
Advises on the proper disposal and recycling of the inverter and its packing materials.
General| Rated Power | 5000 W |
|---|---|
| Number of MPPT Trackers | 2 |
| Nominal AC Voltage | 230 V |
| AC Output Frequency | 50/60 Hz |
| Cooling Method | Natural convection |
| Protection Degree | IP65 |
| Max. AC Power | 5000 VA |
| Operating Temperature Range | -25°C to 60°C |
| Protection Class | Class I |
| Communication | RS485 |
To Next Page