Samsung HW-Q800A - CONNECTING THE SOUNDBAR; Wired Connections Setup; Subwoofer Pairing and Sync Features

ENG - 4
03 CONNECTING THE
SOUNDBAR
Connecting Electrical Power and
Subwoofer
Make sure to rest the AC/DC Adapter at on a table or
the oor. If you place the AC/DC Adapter so that it is
hanging with the AC cord input facing upwards, water
or other foreign substances could enter the Adapter and
cause the Adapter to malfunction.
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
HDMI
NETWORK ID SET
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
NETWORK ID SET
HDMI TO TV
(eARC/ARC)
HDMI IN
HDMI OUT
(TV-ARC)
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
HDMI
HDMI TO TV
(eARC/ARC)
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
HDMI
NETWORK ID SET
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
NETWORK ID SET
HDMI TO TV
(eARC/ARC)
HDMI IN
HDMI OUT
(TV-ARC)
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
HDMI
HDMI TO TV
(eARC/ARC)
DC 19V
POWER
Rear of Subwoofer Bottom of the Soundbar Main Unit
Manually connecting the
Subwoofer
1. Turn off the Soundbar main.
2. Press and hold ID SET on the rear of the subwoofer
for at least 5 seconds.
Rear of Subwoofer
"Blinking blue fast"
5 sec
3. Press the Up button on the remote control for
5 seconds.
SOUND
MODE
PAIR
5 sec
ID SET
4. Check if the LINK LED is solid blue (connection
complete).
• The LINK LED indicator stops blinking and glows
a solid blue when a connection is established
between the Soundbar and the Wireless
Subwoofer.
04 USING A WIRED
CONNECTION
1
HDMI Cable
2
Optical Cable (not
supplied)
HDMI IN
(ARC)
HDMI
HDMI TO TV
(eARC/ARC)
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
HDMI OUT
1
1
Connecting using an HDMI Cable (External Device /
TV ARC)
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
DC 19V
2
Connecting using an Optical Cable (D.IN)
NOTE
• When the TV sound is not output, press the (Multi
Function) button at the top of the Soundbar or the
(Source) button on the remote control to select
the “D.IN” mode. The screen displays “D.IN” and “TV
ARC” in sequence, and TV sound is played.
• The recommended cable is High Speed HDMI Cable
with Ethernet.
• When you use an optical cable and the terminals have
covers, be sure to remove the covers.
Using the Q-Symphony Function
For Q-Symphony, the Soundbar syncs with a Samsung
TV to output sound through two devices for optimum
surround effect. When the Soundbar is connected, the
menu, “TV+Soundbar” appears under the Sound Output
menu of the TV.
• TV menu example: TV + [AV]Soundbar series name
[HDMI]
NOTE
• It can operate according to the Codec supported by
TV.
• This function is supported only when the HDMI Cable
or Optical Cable (not supplied) is connected.
• This function is available in some Samsung TVs and
some Soundbar models.
Spacet
The active sound measured from the TV is synced to the
Soundbar.
NOTE
• Only certain TV models support this function, and the
function is operated from the TV.