Samsung PM32F Quick Setup Guide

Quick Setup Guide
PM32F·PM43F·PM49F·PM55F
PH43F·PH49F·PH55F
• The colour and the appearance may differ depending on the product, and the specications are subject
to change without prior notice to improve the performance.
• Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
BN68-08079J-00
Checking the Components
Contact the vendor where you purchased the product if any components are missing.
Quick Setup Guide Warranty card (Not available in some
locations)
Regulatory guide MagicInfo Software DVD
+
+
-
-
Power cord Batteries (Not available in some locations) Remote Control RS232C(IN) adapter
Screw (M3L8, 1 piece) USB cover
Troubleshooting Guide
Reverse Side
DVI / RGB /
MAGICINFO IN
HDMI2
USB1
RS232C
OUT
RS232C
IN
USB2
AUDIO
IN
HDMI1
AUDIO
OUT
RJ45DP IN
DAISY CHAIN
01
03 04
0602 05
07
08
09
01 Connect to a USB memory device.
02 Connects to MDC using an RS232C adapter.
03 Receives sound from a source device via an audio cable.
04 Connects to the audio of a source device.
05 Connects to a source device using an HDMI cable.
06 DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
RGB IN: Use the (dedicated) D-SUB - DVI cable (or D-SUB cable with D-SUB to DVI
adapter) when connecting a PC.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
07 Connects to a source device using a DP cable.
08 Connects to another product using a daisy chain (DP port) cable.
09 Connects to MDC using a LAN cable.
Issues Solutions
The screen keeps switching
on and off.
Check the cable connection between the product
and PC, and ensure the connection is secure.
No Signal is displayed on the
screen.
Check that the product is connected correctly with
a cable.
Check that the device connected to the product is
powered on.
Not Optimum Mode is
displayed.
This message is displayed when a signal from the
graphics card exceeds the product’s maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set
the maximum resolution and frequency according
to the product specications.
The images on the screen
look distorted.
Check the cable connection to the product.
The screen is not clear.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension cable,
etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears unstable
and shaky.
Check that the resolution and frequency of the
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu and
the Standard Signal Mode Table.
There are shadows or ghost
images left on the screen.
Issues Solutions
The screen is too bright.
The screen is too dark.
Adjust Brightness and Contrast.
Screen color is inconsistent. Go to Picture and adjust the Color Space settings.
White does not really look
white.
Go to Picture and adjust the White Balance settings.
There is no sound. Check the connection of the audio cable or adjust
the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low after turning it up to the
maximum level, adjust the volume on your PC
sound card or software program.
The remote control does not
work.
Make sure that the batteries are correctly in place
(+/-).
Check if the batteries are at.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
[PMF_PM32~55-INDIA-QSG]BN68-08079J-00.indd 1 8/22/2016 4:22:33 PM

Samsung PM32F Specifications

General

Panel life	- h
Color gamut	72 %
Pixel pitch	0.36 x 0.36 mm
Response time	8 ms
Display diagonal	32 \
Display brightness	400 cd/m²
Display technology	LED
Vertical scan range	48 - 75 Hz
Horizontal scan range	30 - 81 kHz
LED backlighting type	Edge-LED
Supported video modes	1080i, 1080p
Display number of colors	1.073 billion colors
Display diagonal (metric)	80 cm
Active display area (W x H)	698.4 x 392.85 mm
Supported graphics resolutions	1920 x 1080 (HD 1080)
Dynamic contrast ratio marketing name	Mega Contrast
USB version	2.0
DVI-I ports quantity	1
VGA (D-Sub) input ports	0
TV tuner integrated	No
Operating hours (hours/days)	16/7
Orientation	Horizontal
Product color	Black
Product design	Digital signage flat panel
Bezel width (top)	6.9 mm
Bezel width (side)	8.9 mm
Panel mounting interface	200 x 200 mm
RMS rated power	20 W
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	85 W
L2 cache	32 KB
Memory clock speed	1866 MHz
Internal memory	2.5 GB
Processor cores	4
Processor model	Cortex-A12
Processor family	ARM Cortex
Processor frequency	1.3 GHz
Audio formats supported	DTS
Image formats supported	PNG
Video formats supported	AVC, AVS, H.263, H.264, MPEG, MPEG1, MPEG2, MPEG4, VC-1, VP8, VP9
Internal storage capacity	8 GB
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 80 %
Cables included	AC
Package depth	132 mm
Package width	796 mm
Package height	484 mm
Package weight	7000 g

Weight and Dimensions

Depth	29.9 mm
Width	721.2 mm
Height	415.6 mm
Weight	5600 g