Samsung SVMI-20E - User Manual

1. Installing the SVMi-20E in an OfficeServ 7200/7400 Series System
When installing an SVMi-20E card, it is important to remember that it is a computer, much the same as any
desktop PC and it is therefore very important not to exceed the environmental limits of an ordinary PC.
I POWER REQUIREMENTS
Because the SVMi-20E card does NOT draw from the -48DC supply it has a Zero (0) SEPU rating under all
possible configurations.
I OfficeServ 7200/7400 Series HARDWARE COMPATIBILITY
When configured for 16 ports or less this card can be installed in any universal slot.When configured for
20 ports the SVMi-20E card must be installed in 32 channel slots.
I OfficeServ 7200/7400 Series SOFTWARE COMPATIBILITY
All versions of the OfficeServ 7200/7400 support the SVMi-20E operation. We have introduced a new 8-
Port VPM daughterboard to reach the 20 ports that requires SVMi-20E software version 5.3.3.5 or higher
and MP software version 4.30h or higher.
2. Inspection
Unpack and inspect the unit for any obvious damage. This card should be labeled SVMi-20E. If it is not, you
have the wrong card. Before inserting the SVMi-20E card in the OfficeServ system install required optional
boards to meet customer’s configuration and requirements.
3. Installing Individual Components on SVMi-20E SBC
3.1 Installing Voice Processing Modules
VPMs are only necessary when more than 4 ports are required on the SVMi-20E.VPMs are NOT required
to access the first four embedded ports. Adding new VPMs is as simple as plugging them with the cor-
rect location for each module.Here is a chart showing the correct location and VPM for this installation.
SVMi-20E Installation / May 2009 1
SVMi-20E INSTALLATION
Configuration
Included on
SBC
VPM in SL2 VPM in SL3 Total Ports
1 4 none none 4 Voice
2 4 VPM-E none 8 Voice
3 4 VPMF-E none 8 Voice Supporting 1 Fax
4 4 VPM-E VPM-E 12 Voice
5 4 VPM-E VPMF-E 12 Voice Supporting 1 Fax
6 4 8VPMF-E none 12 Voice Supporting 1 Fax
7 4 VPMF-E VPMF-E 12 Voice Supporting 2 Fax
8 4 8VPMF-E VPM-E 16 Voice Supporting 1 Fax
9 4 8VPMF-E VPMF-E 16 Voice Supporting 2 Fax
10 4 8VPMF-E 8VPMF-E 20 Voice Supporting 2 Fax
Home Page

Summary

SVMi-20 E Installation Overview

SVMi-20 E Power Requirements

Specifies power requirements for the SVMi-20E card.

SVMi-20 E Hardware Compatibility

Details hardware compatibility requirements for SVMi-20E installation.

SVMi-20 E Software Compatibility

Outlines software compatibility for SVMi-20E operation with specific versions.

SVMi-20 E Inspection

SVMi-20 E Component Installation

SVMi-20 E Voice Processing Module Installation

Guide to installing Voice Processing Modules (VPMs) on the SVMi-20E SBC.

SVMi-20 E Modem Daughter Board Installation

Modem Daughter Board Preparation

Steps to prepare for installing the Modem Daughter Board.

Modem Daughter Board Installation

Procedure for installing the Modem Daughter Board onto the SVMi-20E.

Modem Daughter Board Uninstalling

Instructions for removing the Modem Daughter Board from the SVMi-20E.

SVMi-20 E 64 MB DRAM Module Installation

64 MB DRAM Module Preparation

Steps to prepare for installing the 64MB DRAM Module.

64 MB DRAM Module Installation

Procedure for installing the 64MB DRAM Module onto the SVMi-20E.

64 MB DRAM Module Uninstalling

Instructions for removing the 64MB DRAM Module from the SVMi-20E.

SVMi-20 E KSU Installation

SVMi-20 E Hard Disk Drive Management

Removing SVMi-20 E Hard Disk Drive

Steps for safely removing the Hard Disk Drive from the SVMi-20E.

SVMi-20 E Compact Flash Adapter Management

Installing SVMi-20 E Hard Disk Drive

Procedure for installing the Hard Disk Drive (HDD) onto the SVMi-20E.

Removing SVMi-20 E Compact Flash Adapter

Steps for safely removing the Compact Flash (CF) Adapter.

Installing SVMi-20 E Compact Flash Adapter

Procedure for installing the Compact Flash (CF) Adapter onto the SVMi-20E.

SVMi-20 E System Setup and Configuration

SVMi-20 E Power Up Procedure

Steps to ensure the SVMi-20E is properly powered up and initialized.

SVMi-20 E System Programming

Programming steps required for SVMi-20E setup and initialization.

SVMi-20 E System Shutdown Procedures

SVMi-20 E Initialization

Process to initialize the SVMi-20E after system programming.

SVMi-20 E Hardware Testing

Procedures to test the installed SVMi-20E hardware functionality.

SVMi-20 E Shutdown Procedure One

First procedure for properly shutting down the SVMi-20E system.

SVMi-20 E Optional Equipment Connections

SVMi-20 E Shutdown Procedure Two

Second procedure for properly shutting down the SVMi-20E system.

SVMi-20 E Shutdown Procedure Three

Third procedure for properly shutting down the SVMi-20E system.

SVMi-20 E Serial Communication Setup

Details on connecting a PC to the SVMi-20E via serial communication.

SVMi-20 E Serial and LAN Connections

SVMi-20 E Local Programming via SIO

Steps for setting up local programming using the SIO port.

SVMi-20 E HyperTerminal Setup for SIO

Configuration guide for HyperTerminal for SVMi-20E communication.

SVMi-20 E File Transfer via SIO

Instructions for transferring files using the SIO port and commands.

SVMi-20 E Network Configuration

SVMi-20 E LAN Port Overview

Overview of the LAN port for programming, backup, and upload/download.

SVMi-20 E Local Programming via LAN

Steps for setting up local programming using the LAN port.

SVMi-20 E Advanced Network Settings

SVMi-20 E HyperTerminal Setup for LAN

Configuration for HyperTerminal for LAN-based SVMi-20E communication.

SVMi-20 E Remote Programming via LAN

Guide for remote administration of SVMi-20E via the LAN port.

SVMi-20 E Default IP Address Change

Instructions on how to change the default IP address of the SVMi-20E.

SVMi-20 E IP Configuration Methods

SVMi-20 E IP Configuration via NED

Using the NED editor to modify the socket.cfg file for IP configuration.

SVMi-20 E Network Utility Usage

SVMi-20 E IP Configuration via SCONFIG

Using the SCONFIG utility to create the socket.cfg file for IP configuration.

Samsung SVMI-20E Specifications