Samsung SyncMaster LD220G - 5 Q & a

English - 6
Question Answer
I cannot turn on the monitor. ▷ Connect the power cable again.
There is no image on the screen. ▷ Unplug the power code and replug in.
▷ Connect the USB cable again.
▷ Install the USB driver.
▷ As USB port can be unstable, reboot your PC.
▷ PC'sUSBportmaybefaulty.Pleasetrytoconnectdifferentport.
▷ USB monitor may not work on USB 1.0.
▷ Any input from mouse or keyboard will activate the display if it is under the
power saving mode.
Ican'tinstallUSBDriverwiththe
supplied CD.
Download USB driver at Samsung Electronics website and install it.
[ http://www.samsung.com ]
After installing USB Driver, The
computer performance is slow.
As USB Driver takes more memory than the use of general graphic card,
computer performance may be lower than before.
After booting the PC, screen order is
changed.
Update your graphic card to the latest version.
N Forgraphiccarddriver,refertographiccardmanufacturer'shomepage.
Monitor resolution is changed. Pleasemakeareferenceto[USBMonitorInstallationguide]-'Display
InformationSetupforUSBMonitor'forbestresolution(►Page5).
[Best Resolution - LD190G: 1360X768, LD220/LD220G: 1920x1080]
Whileplayinghighqualityvideole,
choppy video can be seen repeatedly.
Whenyouwatchhighqualityvideoleinfullscreenmode,itmayplayproperly
due to limited USB bandwidth. It is strongly recommend to decrease the window
size of the movie player.
Depending on PC interface or incompatible codec packs, it can cause serious
playbackissues,suchasickeringorchoppyvideoonthescreen.
IcanuseClonemode,butcan'tsetto
extend mode.
▷ Update your graphic card to the latest version.
NForgraphiccarddriver,refertographiccardmanufacturer'shomepage.
▷ Rightclick'Desktop'-'Property'-'Settings'tab.Check'Extendmywindows
desktopontothismonitor'.
▷ If graphic card does not support WDDM, Extend mode can not be used in
windows Vista. e.g.,) Some versions in Matrox Card
How can I remove the “USB Monitor
Installation Program” completely?
1. Click ‘Add/Remove Programs’ in the ‘Control Panel’. A list of ‘Currently Installed
Programs’ is displayed.
2. Select ‘Samsung UbiSync Monitor’ from the list and click ‘Remove’.
I disconnected or turned off my USB
monitor but my PC still displays the
old monitor information in the Display
Properties window.
Deactivated USB monitor is due to either the power is off or there is no USB
connection.
Inordertoremovethisinformation,'SamsungUbisyncMonitor'programmust
beremoved.Thiscanbedonebyclick'Start'-'ControlPanel'-'Add/Remove
Programs'-'SamsungUbisyncMonitor'-'Remove'.
All the connected USB monitors will not be able to use if the software program is
removed.
Installation software program must be installed again in ordr to use USB monitor.
The screen of USB monitor is frozen. Check "Hardware Acceleration" on desktop property.
1.Click'Start>ControlPanel>AppearanceandThemes>Display>Settings>
Advanced'.
2.Select'Troubleshoot'tab,whendisplayed.
Set the ‘Hardware acceleration(H)’ value to ‘Full’.
Icons and photos are broken or
jagged in Clone mode (USB monitor).
This occurs because Windows does not send the screen updating information to
Clone mode if Extended mode is active on a single PC. We recommend using the
monitor in Extend mode.
5. Q & A
BN68-02216B-00.indb 6 2009-03-05 �� 3:49:58