WEA463e Quick User Guide
Base
Console Port, Factory Reset Switch
Ethernet Port (PoE)
DC Input
Ethernet PortBackhaul LED
LED Status
Indicator
Interface
Interface Description
LED Status Displays the status information of WEA463e using an LED.
DC Input Connects the power adaptor.
Ethernet Port
(PoE)
Supports a 1000 BASE-T Gigabit Ethernet and PoE IEEE
802.3af/802.3at connection.
Console Port Used to check the operational status of the WEA463e and to input the CLI.
Factory
Reset Switch
Used to switch the WEA463e to the initial factory settings.
LED Status Indicator
LED Status Description
System Start White Initial LED status
Blue Device reset and diagnostic test in
progress
Red Booting failure (device reset failure)
Provisioning Repeating red and green Connecting APC (network link normal)
Blinking green Connecting CAPWAP (APC server
connection status normal)
Normal
Operations
Green No wireless UE connected
Blue Wireless UE connected
Upgrade Blinking blue Upgrading software
Failure Blinking red Network connection failure (physical)
Blinking orange IP address conflict
Blinking violet Dynamic IP address allocation failure
Blinking bluish green Network connection failure (logical)
Repeating Red and Blue Wireless interface failure
Backhaul LED
LED Stuatus and description
Connection Ready White LED On
Connection Complete If connected with AP, LED blinks red, white, green, blue color
sequentially according to signal strength.
※
LED turns off when it does not configured for Mesh AP.
Installation
The WEA463e can be installed on a pole or on a wall.
Please confirm that all of the components have been included before installation.
Install the product in a vertical position and ensure that I/O ports are facing down.
Before Installation
Safety Requirements
Carefully observe the following safety warnings in order to avoid the risk of
damage or injury. Always follow these safety precautions when using the product.
- There is a risk of electrical shock. Make sure that the
power is turned off during installation. Do not proceed with
the installation if there is any electrical current leaking.
It may cause a serious electric shock.
- Wear anti-static gloves or take an appropriate action to
prevent ESD when handling the product.
- Do not connect a phone line to an Ethernet port.
This may damage the product.
- This product must be connected to a power supply in
compliance with IEEE 802.3af/at or connected to a limited
power supply in compliance with IEC/EN/UL 60950-1.
- This product must be installed or removed by only
appropriately trained service personnel.
- For outdoor use or installation outdoors. For more details,
refer to “Environment” in the IEEE 802.3af/at standards.
- This product must be installed at least 3 m or further away
from a WiBro/3G/4G repeater or antenna.
This manual describes the Wireless Enterprise WEA463e
configuration and installation instructions.
Introduction
What is WEA463e?
The WEA463e is an 802.11ac-based outdoor Wireless Enterprise AP that
supports Mesh Networking. It connects the UE that supports wireless LAN,
such as a smartphone, tablet, or notebook, to a wired network in an outdoor
environment.
The WEA463e supports the following features:
- IEEE 802.11a/b/g/n/ac standard
- Power over Ethernet (PoE) IEEE 802.3af/802.3at
- 3 × 3 Multiple Input Multiple Output (MIMO)
- Wireless LAN through both 2.4 GHz and 5 GHz bandwidths
- Temperature Range: -40~+55°C
- Environment Condition: IP66 & IP67
Components
After unpacking the WEA463e, confirm that all of the following items have been
included:
Front Rear
Common Components
Mount, Unit Bracket
Waterproof Connector
for Ethernet Cable, Installation Guide
6 M4 × L10 Screws Quick Start Guide
Wall-Mount Installation Materials
5 plastic Anchors 5 M4 × L25 Screws
It is recommended that you keep the box and all of the
packing materials.
Name and Function
Side
Ground Wire
To Next Page
Need help?
General
