Sandberg Basic Ken Taylor User Manual

1
4
5
2
3
6
1
2
4
5
3
Split Switch: Der Tonabnehmer Split Schalter schaltet beide Humbucker (Steg- und
Hals-Pickup) zu Single Coil Pickups ( nur die hals- seitigen Spulen laufen) um.
Schalter in Richtung Hals = beide Tonabnehmer umgeschaltet (Single Coil), Schalter
in Richtung Steg = beide Tonabnehmer Humbucker.
Split Switch: the pickup split switch splits both humbuckers ( bridge pickup and neck
pickup ) to single coil pickups ( only neck direction coils working ). Switch pushed in neck
direction = both pickups split, switch pushed in bridge direction = both humbucker.
6
Volume Push/Pull: Durch herausziehen des Lautstärke Reglers wird die aktive
Elektronik umgangen (passiver Modus).
Das Instrument funktioniert im passiven Modus auch ohne eingelegte Batterie.
Volume Push/Pull: By pulling the Volume knob, the active electronic will be bypassed
(passive mode). The Instrument works in passive mode even without battery if needed.
Treble: Drehen des Knopfes im Uhrzeigersinn erhöht Treble. Drehen gegen den
Uhrzeigersinn verringert Treble.
Treble: Tone Controls. Turn the knob clockwise to boost Treble. Turning the knob
counter clockwise will cut the tone.
Balance: In der Mittelstellung sind beide Tonabnehmer gleich laut. In Richtung
eines Pickups gedreht, verändert sich das Verhältnis zu Gunsten des ausgewählten
Tonabnehmers.
Balance: Used for pickup selection. Turn the knob into the direction of the pickup you
want to use. In center position both pickups run 100%.
Midrange: Drehen des Knopfes im Uhrzeigersinn erhöht Midrange. Drehen gegen
den Uhrzeigersinn verringert Midrange.
Midrange: Tone Controls. Turn the knob clockwise to boost Midrange. Turning the
knob counter clockwise will cut the tone.
Bass: Drehen des Knopfes im Uhrzeigersinn erhöht Bass. Drehen gegen den Uhrzei-
gersinn verringert Bass.
Bass: Tone Controls. Turn the knob clockwise to boost Bass. Turning the knob counter
clockwise will cut the tone.
7
Klinkenbuchse: Bitte darauf achten, dass der Stecker des Instrumentenkabels
richtig (zwei Mal) eingerastet ist, sonst funktioniert der Bass nicht im aktiven
Modus.
Input Jack: Please make sure the instrument cable is set in correctly (clicked two times),
otherwise the bass will not work in active mode.
7
all_sandberg-einleger_1707_2009.qxp:Layout 1 21.07.2009 15:06 Uh

Sandberg Basic Ken Taylor Specifications

General

Brand	Sandberg
Model	Basic Ken Taylor
Category	Musical Instrument
Language	English

Summary

Ken Taylor Bass Controls and Features

Volume Push/Pull for Active/Passive Mode

Pulling the volume knob bypasses active electronics for passive mode operation.

Treble Tone Control

Boosts treble clockwise and cuts treble counter-clockwise.

Pickup Balance Control

Adjusts pickup blend. Center is 100% for both pickups.

Midrange Tone Control

Boosts midrange clockwise and cuts midrange counter-clockwise.

Bass Tone Control

Boosts bass clockwise and cuts bass counter-clockwise.

Pickup Split Switch Functionality

Splits humbuckers to single coils. Neck position splits both, bridge keeps humbucker.

Input Jack for Active Mode

Ensure cable is fully plugged in for active mode to function.

General Notice and Battery Management

Active Electronics and Battery Life

Active preamps engage via input jack; unplug cable when not in use to prolong battery life.