The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use
of such marks by SANGEAN ELECTRONICS INC. is
under license.
Important safety instructions
1. Do not install near any heat sources such as
radiators, heat registers, stoves or other apparatus
(including amplifiers) that produce heat.
2. Only use attachments / accessories specified by
the manufacturer.
3. To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
4. Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, shall
not be placed on the apparatus.
5. The batteries shall not be exposed to excessive
heat such as sunshine, fire or the like.
6. Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment and warranty.
7.
CAUTION
Risk of explosion if the battery is replaced by an
incorrect type.
8. Do not allow your radio to be
exposed to water, steam or sand.
9. Do not leave your radio where
excessive heat could cause damage.
10. If safety relevant, the following information should
be included as far as applicable:
1 2 3
● minimumdistances around the apparatus for
sufficient ventilation;
● theventilationshouldnotbeimpededby
covering the ventilation openings with items,
such as newspaper, table-cloths, curtains, etc.;
● nonakedflamesources,suchaslighted
candles, should be placed on the apparatus;
● attentionshouldbedrawntotheenvironmental
aspects of battery disposal;
● theuseofapparatusintropicaland/or
moderate climates.
11.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
12. If an apparatus is provided with a replaceable
lithium battery, the following applies:
● ifthebatteryisintendedtobereplacedby
the user, there shall be a warning close to the
battery or in both the instruction for use and
service instructions;
● ifthebatteryisnotintendedtobereplacedby
the user, there shall be a warning close to the
battery or in the service instructions.
Controls
1
Preset button
2
LCD display
3
Source button
4
Menu / Info button
5
Select / Play / Pause button
6
Sleep / Light button
7
Power button / Volume control knob
8
Bass reflex tube
9
Tuning control knob
10
Speaker
11
3.5mm external antenna socket
12
3.5mm auxiliary input socket
13
DC IN 5V / 2.4A USB charging socket
Using the touch panel
The CP-100D has a stylish touch panel instead
of conventional buttons. To operate the buttons
simply touch the button area with the tip of a
finger for about half a second. The sleep time and
system menu functions marked with a dot ( ● ) are
accessed by means of a long touch (2-3 seconds)
on the appropriate button until the display on the
radio shows that the command has been accepted.
You may find at first that the radio does not always
detect that you have touched a button. If so, try
touching with a little more pressure, or for slightly
longer. You will soon find the optimum touch
needed to control your radio. The panel may be
cleaned using a dry cloth. Do not use abrasives,
cleaning fluids or solvents.
NOTE
The control panel would be auto dimmed into
sleep mode when not in use. Tap any function
button on the panel to bring the backlight back
on without triggering its function, the second
touch will then execute the function.
4 5 6 7 8 9
Manual tuning – DAB
Manual tuning allows you to tune directly to the various
Band III DAB channels (5A to 13F).
1. When in DAB mode press and hold the Menu button
to enter the DAB menu.
2. Rotate the Tuning control knob to select “Manual
Tune”.
3. Press the Select button to enter manual tune option.
4. Rotate the Tuning control knob to choose the
required DAB channel.
5. Press the Select button to cause the radio to tune to
the chosen channel.
Station order setup – DAB
Your radio has 3 station order settings from which
you can choose. The station order settings are
alphanumeric, ensemble and valid.
1. When in DAB mode press and hold the Menu button
to enter the DAB menu.
2. Rotate the Tuning control knob to select the “Station
Order”.
3. Press the Select button to enter the station order
adjustment mode.
4. Rotate the Tuning control knob to choose
“Alphanumeric”, “Ensemble” and “Valid”.
“Alphanumeric” - sorts the station list alpha-
numerically 0...9 A...Z.
“Ensemble” - organizes the station list by DAB
multiplex.
“Valid” - shows only those stations for which a signal
can be found.
5. Press the Select button to confirm the required
station order.
Dynamic Range Control settings –
DAB
Dynamic Range Control (also known as DRC) can
make quieter sounds easier to hear when your radio is
used in a noisy environment by reducing the dynamic
range of the audio signal.
1. When in DAB mode press and hold the Menu button
to enter the DAB menu.
2. Rotate the Tuning control knob to select the “DRC
Value”.
3. Press the Select button to enter the DRC adjustment
mode.
4. Rotate the Tuning control knob to highlight the
required DRC setting (the default is Off).
Off - DRC is switched off, Broadcast DRC will be
ignored.
Low - DRC level is set to 1 / 2 that sent by broadcaster.
High - DRC is set as sent by broadcaster.
5. Press the Select button to confirm the setting.
NOTE
Not all DAB broadcasts use the DRC function. If the
broadcast does not provide DRC information, then
the DRC setting in the radio will have no effect.
Prune stations – DAB
If you move to a different part of the country, some
of the stations which were listed may no longer be
available. Also, from time to time, some DAB services
may stop broadcasting, or may change location or
frequency. Stations which cannot be found, or which
have not been received for a very long time are shown
in the station list with a question mark. The Prune
stations function will delete the marked DAB stations
from your station list.
1. When in DAB mode press and hold the Menu button
to enter the DAB menu.
2. Rotate the Tuning control knob to select the “Prune
Station”.
3. Press the Select button to enter adjustment mode.
4. To activate the Prune function, rotate the Tuning
control knob to select “Yes”. Press the Select button
to confirm the setting. If you do not wish to prune
stations, choosing “No” or “Back” will go back to the
previous menu display. Press the Select button to
confirm your choice.
NOTE
If you have moved your radio to a different part of
the country you should also carry out a search for
new stations (please see the section 'Finding new
stations').
Operating your radio – FM
1. Insert the (supplied) external antenna plug into the
external antenna socket located on the rear of your
radio.
2. Press the Power button to switch on your radio.
3. Press the Source button to select the FM band.
4. Press and hold the Menu button to enter the FM
menu.
5. Rotate the Tuning control knob to select “SCAN”.
Press the Select button to cause your radio to
search from low frequency to high frequency. When
it finds a station of sufficient strength, the frequency
will flash 6 seconds on the display and the radio
will continue to scan after 6 seconds. To tune to
the station or stop the scanning, press the Select
button.
6. The display will show the frequency of the signal
found. If the signal is strong enough and there is
RDS data present then the radio will display the
station name.
7. When the end of the waveband is reached your
radio will recommence tuning from the opposite end
of the waveband.
8. Rotate the Volume control knob to adjust the sound
level as needed.
9. To switch off your radio, press the Power button.
Manual tuning – FM
When in FM mode, rotate Tuning control knob to tune
to a station.
Scan sensitivity setting – FM
Your radio includes a local / distant option for the auto-
scan function. By setting the radio to the “local” scan
option, weaker signals from more distant transmitters
can be ignored by the radio, making stronger signals
easier to find.
1. When in FM mode, press and hold the Menu button
to access FM menu.
2. Rotate the Tuning control knob to select “FM Scan
Zone”. Press the Select button to enter the scan
sensitivity adjustment mode. The current setting will
be marked with an asterisk.
3. Rotate the Tuning control knob to select “Local”
(Strong stations only) or “Distant” (All stations). The
“Distant” option will allow the radio to find weaker
signals when scanning.
4. Press the Select button to confirm your selection.
The setting is stored in the radio and remains in
force until changed or until a System reset.
Presetting stations in DAB and FM
modes
There are 10 presets each for DAB and FM radio.
They are used the same way for each operating mode.
1. Press the Power button to switch on your radio.
2. Tune to the required radio station as previously
described.
3. Press and hold the Preset button to enter the Preset
Station menu.
4. Rotate Tuning control knob to scroll through the
preset list until you reach an unused preset or a
preset that you wish to change.
5. Press Select button to store the preset. “Preset 2
saved” for example will be shown on the display.
6. Repeat this procedure as needed for the remaining
presets. Stations which are already stored in the
presets may be overwritten by following the above
procedure.
NOTE
The radio station presets are retained in memory
when the radio is switched off.
Recalling a preset in DAB and FM
modes
1. Press the Power button to switch on your radio.
2. Select the required operating mode using the
Source button.
3. Press the Preset button to enter the Recall Station
menu.
4. Rotate Tuning control knob to select the desired
preset station. Press the Select button. Your radio
will then tune to the station stored in the selected
preset memory. The chosen preset number is also
shown in the display, e.g. “P2”.
Display options – DAB / FM /
Bluetooth
Your radio has a range of display options when in
DAB, FM and Bluetooth modes:
Press the Info button to cycle through the various
options.
DAB display options
Your radio can display the following in DAB mode:
Scrolling text, Program type, Multiplex name, Time
/ Date, Frequency, Bit rate and audio type, Coding
information, DL Plus text, Signal strength.
For the DL Plus text, some stations may provide
other programme related information for the display
in addition to the regular text. If none is available, a
message ‘no info’ is displayed.
FM display options
In FM mode your radio can use the Radio Data System
(RDS) to display the radio station name and additional
text when provided by the broadcaster and where the
radio signal is sufficiently clear.
Your radio can display the following in FM mode: Radio
Text, Program Type, Time / Date, Frequency.
Bluetooth display options
If your connected device is able to provide information
from the track being played, your radio can display the
following in Bluetooth mode:
Device Name, Title, Artist, Album.
Please note that the availability of information depends
on the specific media format.
Listening to music via Bluetooth
streaming
You need to pair your Bluetooth device with your
CP-100D before you can auto-link to play / stream
Bluetooth music through your CP-100D. Pairing
creates a ‘bond’ so the two devices can recognize
each other.
Pairing and playing your Bluetooth
device for the first time
1. With your radio switched on, press the Source
button to select Bluetooth function. “Bluetooth
Pairing” will show on the display. The LED indicator
around the Power button will flash a fast blue to
show the radio is discoverable.
(While charging in Bluetooth mode, the LED
indicator around the Power button will cycle
between red and purple.)
2. Activate Bluetooth on your device according to the
device’s user manual to link to the radio. Locate the
Bluetooth device list and select the device named
“CP-100D” (With some Smartphone’s that are
equipped with earlier versions than BT2.1 Bluetooth
device, you may need to input the pass code “0000”).
3. Once connected, there will be a confirmation tone
sound and the name of your connected Bluetooth
device will show on the display. The LED indicator
around the Power button will turn a solid blue. (While
charging in the Bluetooth mode, the LED indicator
around the Power button will turn a solid purple.)
You can simply select and play any music from your
source device.
4. The volume control can be adjusted from your
source device, or directly from the radio. Use the
controls on your Bluetooth-enabled device or on the
radio to play / pause and navigate tracks.
● If 2 Bluetooth devices are pairing for the first
time, both will search for your radio, it will show
its availability on both devices. However, if one
device links with this unit first, then the other
Bluetooth device will not find it on the list.
● If you take your source device out of range, the
connection will be temporarily disconnected to
your radio. Your radio will automatically reconnect
if the source device is brought back in range. Be
aware that during the period of disconnection, no
other Bluetooth device can pair or link with your
radio.
● If “CP-100D” shows in your Bluetooth device list
but your device cannot connect with it, please
delete the item from your list and pair the device
with the radio again following the steps described
previously.
● The effective operation range between the system
and the paired device is approximately 10 meters
(30 feet). Any obstacle between the system and
the device can reduce the operational range.
● Bluetooth connectivity performance may vary
depending on the connected Bluetooth devices.
Please refer to the Bluetooth capabilities of
your device before connecting to your radio. All
features may not be supported on some paired
Bluetooth devices.
● With some mobile phones, making / receiving
calls, text messages, e-mails or any other
activities unrelated to audio streaming may mute
the Bluetooth audio streaming or even temporarily
disconnect from your device. Such behavior is a
function of the connected device and does not
indicate a fault with your CP-100D.
NOTE
Playing audio files in Bluetooth mode
When you have successfully connected your radio with
the chosen Bluetooth source device you can start to
play your music using the controls on your connected
Bluetooth device.
1. Once playing has started adjust the volume to the
required setting using the Volume control on your
radio or on your enabled Bluetooth source device.
2. Use the controls on your Bluetooth source device
to play / pause and navigate tracks. Alternatively,
control the playback using Tuning control knob
on your radio. Rotate the Tuning control knob in a
clockwise direction to play next track. Rotate the
Tuning control knob in an anti-clockwise direction
to play previous track. Press the Select button to
pause / play the track.
NOTE
Not all player applications or devices may respond to
all of these controls.
Reconnecting a previously-paired
Bluetooth source device
The CP-100D can memorize up to 8 sets of paired
Bluetooth source devices, when the memory exceed
this amount, the earliest paring device will be over
written from the device.
If your Bluetooth source device already paired with
the CP-100D previously, the unit will memorize your
Bluetooth source device and it attempts to reconnect
with a Bluetooth source device in memory which is
last connected. If the last connected Bluetooth source
device is not available, the CP-100D will try to connect
to the second last Bluetooth source device.
Disconnecting your Bluetooth device
1. Press and hold the Menu button to enter the
Bluetooth menu.
2. Rotate Tuning control knob to select “Cancel
Pairing”. Then press the Select button.
3. To disconnect with your Bluetooth device, rotate
Tuning control knob to select “Yes” and then press
the Select button. There will be a confirmation tone
sound and the LED indicator around the Power
button will flash a fast blue to show the radio is
discoverable again for pairing. Choosing “No” or
“Back” will go back to the previous menu display.
Press the Select button to confirm your choice.
4. Alternatively, you can press the Source button to
select any mode other than Bluetooth mode or turn
off Bluetooth on your Bluetooth device to disable the
connection.
Deleting Bluetooth paired device
memory
1. Press and hold the Menu button to enter the
Bluetooth menu.
2. Rotate Tuning control knob to select “Clear Pairing”.
Then press the Select button.
3. To clear the memory of all paired devices, rotate
Tuning control knob to select “Yes”. Then press
the Select button. Choosing “No” or “Back” will go
back to the previous menu display. Press the Select
button to confirm your choice.
Contrast
The contrast of the display can be adjusted.
With your radio switched on, press the Light button
to adjust the required contrast. The contrast level
indication on the screen will change at the same time.
Sleep timer
Your radio can be set to turn off after a preset time
has elapsed. The sleep timer setting can be adjusted
between 15 and 120 minutes in increments.
1. With your radio switched on, press and hold the
Sleep button to enter the sleep setup menu.
2. Rotate the Tuning control knob to select the required
sleep time. The sleep timer can be set to between
15 and 120 minutes, or select “Sleep off” to cancel
the sleep timer. Press the Select button to confirm
the setting.
3. Alternatively press and hold the Menu button to
access the menu for the current mode.
4. Rotate the Tuning control knob to select “System
Setup”. Press the Select button.
5. Rotate the Tuning control knob to select “Sleep”.
Press the Select button.
6. Rotate the Tuning control knob to select the required
sleep time. Or select “Sleep off” to cancel the sleep
timer. Press the Select button to confirm the setting.
7. An active sleep timer is shown using a sleep timer
icon on the playing displays. To view the remaining
time of an active sleep timer, press and hold the
Sleep button to view the remaining time.
Alternatively press and hold the Menu button and
then rotate the Tuning control knob to select “System
Setup”. Press the Select button. Rotate the Tuning
control knob to select “Sleep”. Press the Select
button to view the remaining time.
8. To cancel the sleep time before the preset time has
elapsed and to turn off the radio, press the Power
button to turn the radio off manually.
Automatically updating the clock
Your radio will automatically update each time you turn
on the radio and tune to a DAB+ radio station or to an
FM station which is broadcasting the time via RDS.
Time display will flash 00:00 for a few seconds then
display the clock time when it receives DAB+ or FM-
RDS clock time signal. You may specify that the radio
sets its clock from DAB or FM radio broadcasts.
1. With your radio switched on, press and hold the
Menu button to access the menu for the current
mode.
2. Rotate the Tuning control knob to select “System
Setup”. Press the Select button to enter the system
settings menu.
3. Rotate the Tuning control knob to select “Time
setup”. Press the Select button.
4. Rotate the Tuning control knob to select “Time
update”. Press the Select button to enter the setting.
5. Rotate the Tuning control knob to choose an update
option from “DAB”, “FM” or “Any” as required. Press
the Select button to confirm your choice.
Time display
1. With your radio switched on, press and hold the
Menu button to access the menu for the current
mode.
2. Rotate the Tuning control knob to select “System
Setup”. Press the Select button.
3. Rotate the Tuning control knob to select “Time
setup”. Press the Select button.
4. Rotate the Tuning control knob to select “Time
display”. Press the Select button.
5. Rotate the Tuning control knob to select “Enable” or
“Disable”. Select "Enable" to display the time. Select
"Disable" and the time display will disappear. Press
the Select button to confirm your choice.
Language selection
By default your radio will display all menus and
messages in English. You can choose your preferred
language.
1. With your radio switched on, press and hold the
Menu button to access the menu for the current
mode.
2. Rotate the Tuning control knob to select “System
Setup”. Press the Select button to enter the system
settings menu.
3. Rotate the Tuning control knob to select “Language”.
Press the Select button to enter the setting menu.
4. Rotate the Tuning control knob to select your
desired language. Press the Select button to confirm
the setting. The display will change to the chosen
language.
Factory reset
If you wish to completely reset your radio to its
initial state this may be performed by following this
procedure. By performing a factory reset, all user
entered settings will be erased.
1. With your radio switched on, press and hold the
Menu button to access the menu for the current
mode.
2. Rotate the Tuning control knob to select “System
Setup”. Press the Select button to enter the system
settings menu.
3. Rotate the Tuning control knob to select “Factory
reset”. Press the Select button to enter the setting.
Touch panel sensitivity control
The sensitivity of the touch panel may be adjusted.
The default setting will normally be found to
provide satisfactory operation, however, the touch
panel system may respond differently depending
upon the moisture of the skin. The touch panel
sensitivity may be reduced or increased relative to
the standard setting.
1. Press the Power button to switch on your radio.
2. Press and hold the Menu button to access the
menu for the current mode.
3. Rotate the Tuning control knob to select “System
Setup”. Press the Select button to enter the
system settings menu.
4. Rotate the Tuning control knob to select
“Touchpad sensitivity”. Press the Select button
to enter the setting.
5. Rotate the Tuning control knob to select your
desired touch panel sensitivity level (1~5). The
higher the value, the higher the sensitivity. The
default setting is 3. Press the Select button to
save your setting.
Charging the radio
The radio operates on a built-in Lithium-ion
battery that can be recharged either using the
USB charging port or from a USB power adaptor
(not included) with a rated output of DC 5V, 2.4A.
Reduced power, distortion, ‘stuttering’ sounds or
"Low Battery" shows on the display are all signs
that the battery needs to be recharged. When "Low
Battery" appears on the screen, the LED indicator
around the Power button will flash white.
Before operating the radio for the first time please
fully charge the battery.
You can begin using the radio while charging.
Please be aware that in this case make sure
the USB power source can provide 5V 2.4A of
electrical current. If not, it may damage the USB
power source.
●
Connect the (supplied) micro USB plug to the
micro USB charging port on the rear of the
unit.
●
Connect the (supplied) standard USB plug
end of the cable to a power USB port on a
computer or other USB charging device. When
the battery is charging, the LED indicator
around the Power button will be solid red. After
the battery is fully charged, the red charging
indicator will turn off.
NOTE
Operating your radio – DAB
1. Insert the (supplied) external antenna plug into
the external antenna socket located on the rear
of your radio.
2. Press the Power button to switch on your radio.
3. If this is the first time the radio is used, a quick
scan of the Band III DAB channels will be
carried out. If the radio has been used before
the last used station will be selected.
4. During the scanning process, as new stations
are detected the station counter will increase
and the stations will be added to the list which is
stored in the radio. The bar graph indicates the
progress of the scan.
5. When the scanning is completed the first station
(in numeric-alpha order 0...9...A....Z) will be
selected.
6. If the station list is still empty after the scan,
your radio will show “No Service”. If no signals
are found it may be necessary to relocate your
radio to a position giving better reception.
Selecting a station – DAB
1. Press the Power button to switch on your radio.
2. Press the Source button to select DAB radio
mode.
3. Rotate Tuning control knob to scroll through the
list of available stations. Alternatively to access
the station list using the DAB menu, press and
hold the Menu button and then rotate Tuning
control knob to choose 'Station List'.
4. Press the Select button to select and tune to the
desired station.
5. Rotate the Volume control knob to set the sound
level as needed.
NOTE
If after selecting a station the station does not
tune it may be necessary to relocate your radio
to a position giving better reception.
Secondary services – DAB
Some radio stations may have one or more
additional broadcasts associated with them. If
these are available, they will appear immediately
after the main station as you rotate the Tuning
control knob. To tune to the selected service, press
the Select button.
Finding new stations – DAB
As time passes new stations may become
available or you may have moved your radio to a
different part of the country. In this case you may
need to cause your radio to scan for new stations.
1. When in DAB mode, press and hold the Menu
button to enter the DAB menu.
2. Rotate Tuning control knob to select “Full Scan”.
3. Press the Select button. Your radio will perform
a scan of the Band III DAB channels. As new
radio stations are found the station counter on
the display will increase and the radio stations
will be added to the list stored in the radio.
4. Rotate the Tuning control knob to select “Yes”
or “No”. If you do not wish to carry out a system
reset, select “No” and then press the Select
button to confirm the setting. Or choosing “Back”
will go back to the previous menu display. Press
the Select button to confirm your choice.
5. With “Yes” selected, press the Select button to
reset the radio. It will erase all saved settings
and preset memory stations. All settings will
revert to factory default settings.
Software version display
The software version display is provided for
reference and customer support purposes and
cannot be changed.
1. With your radio switched on, press and hold the
Menu button to access the menu for the current
mode.
2. Rotate the Tuning control knob to select “System
Setup”. Press the Select button to enter the
system settings menu.
3. Rotate the Tuning control knob to select “SW
version”. Press the Select button to display the
software version.
Auxiliary input socket
A 3.5mm stereo Auxiliary Input socket is provided
on the rear of your radio to permit an audio signal
to be fed into the unit from an external audio
device such as iPod, MP3 or CD player.
1. With your radio switched on, press the Source
button until “Aux In” is displayed.
2. Connect an external audio source (for example,
iPod, MP3 or CD player) to the Auxiliary Input
socket.
3. Adjust the volume setting on your iPod, MP3 or
CD player to ensure an adequate signal level
from your device. Then adjust the Volume on
the radio as needed for comfortable listening.
Specifications
Frequency Coverage
FM 87.5-108 MHz
DAB 174.928-239.200 MHz
Amplifier
Output power 1.5W 10%T.H.D. @ 100Hz
Aux In
Input sensitivity IN 400mV Output 1.5W @ 100Hz
Speaker
Speaker 50mm 4ohm x 1
Bluetooth
Bluetooth
specification
Bluetooth
®
Ver 5.0
Profile Support A2DP
Bluetooth Audio
CODEC
AAC, SBC
Transmitting Power Specification Power Class 2
Line of sight range 10meters / 30feet
The frequency and
maximum transmitted
power
2402MHz ~ 2480MHz: 3.857dBm
(bluetooth EDR)
Built-in Battery
Battery
Rechargeable Lithium-ion battery
18650 3.63V 2600mAh
Battery life
Speaker output 10mW, the
battery life is approx.20 hours for
4 hours a day at normal volume
level.
General
DC-IN USB TYPE-C jack 5V 2.4A
Charging current 1A
Charging time approximately 5.0 Hr
Operating
temperature range
0°C to +35°C
※
The barcode label on the product is defined as
below:
Serial number
Production month
Production year
Product code
The company reserves the right to amend the
specifications without notice.
If at any time in the future you should need
to dispose of this product please note that:
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice. (Waste Electrical and Electronic
Equipment Directive).
Operating instruction
3A81dQ1000GB0
GB
CP-100D
DAB+ / FM RDS Receiver
With Bluetooth Speaker
1 2
8
3 4
To Next Page
Loading...
