SANLI GTS26 - User Manual

30 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

PLEASE KEEP THIS MANUAL IN A SAFE PLACE

Engine-powered brush cutter

www.sanli.co.uk

Table of Contents

Questions and Answers

P
Philip CollinsJul 31, 2025
What to do if my SANLI Brush Cutter does not start?
- R
  Ronald MilesJul 31, 2025
  If your SANLI Brush Cutter doesn't start, several factors could be at play. First, ensure the « Start/Stop» switch is in the START position. Check if the air filter is dirty and clean or replace it if necessary. Inspect the spark plug for dirt; clean it and set the electrodes at 0.5 mm, or replace it if it's old. Make sure there is enough fuel in the tank and that the fuel mixture isn't old or of bad quality, in that case, drain the tank and refill with fresh 2 stroke mixture. If these steps don't resolve the issue, the carburettor may be obstructed or badly set, or the exhaust pipe could be blocked, requiring professional attention from a SANLI approved repairer or cleaning/replacement, respectively.
M
Michele BonillaAug 11, 2025
Why the cutting line doesn’t come out of my SANLI Brush Cutter?
- J
  Julie WallaceAug 11, 2025
  If the cutting line of your SANLI Brush Cutter doesn’t come out, it could be due to an empty line spool. In this case, replace the wire spool. Alternatively, the automatic nylon line feeding system might be dirty. Try dismantling and cleaning the line and its support.
V
vicki35Aug 20, 2025
What to do if the engine works but the spool doesn’t move on my SANLI GTS26?
- E
  Eric WilliamsAug 20, 2025
  If the engine of your SANLI Brush Cutter is running but the spool isn’t moving, the spool might be blocked by cutting debris. Stop the device and remove any objects blocking the spool. Another possibility is a faulty or worn transmission, which would require a SANLI- approved repairer to dismantle it.

Summary

Detailed Description of the Petrol Brush Cutter

1. Introduction

2. Safety instructions

2.1 Safety labels and symbols

Explains safety symbols used in the manual and on the tool for safe operation.

2.2 Before using the petrol brush cutter

Crucial pre-operation checks, warnings, and limitations for safe use.

2.3 When using the petrol brush cutter

Key safety guidelines and precautions during brush cutter operation.

2.4 After using the petrol brush cutter

Post-operation safety measures and checks for the brush cutter.

3. Usage Guidelines

3.1 Preparation of the petrol brush cutter

Steps to prepare the brush cutter before use, including assembly.

3.11 Setting up the petrol brush cutter

Details on attaching handles and ensuring proper assembly.

3.12 Filling up with fuel

Instructions and warnings on how to refuel the brush cutter safely.

3.2 Using the petrol brush cutter

General advice and checks before operating the brush cutter.

3.21 Starting the brush cutter

Step-by-step guide for starting the brush cutter, distinguishing between cold and hot engines.

3.22 Stopping the brush cutter

Procedure for safely stopping the brush cutter's engine.

3.23 Adjusting the cutting wire during use

How to automatically extend and adjust the cutting line length during operation.

3.24 Advice for cutting

Guidance on cutting techniques, avoiding obstacles, and preventing kickback.

3.25 Changing the nylon line

Step-by-step instructions for replacing the nylon cutting line spool.

3.3 Cleaning, storage, transport and maintenance

Overview of cleaning, storage, and transportation procedures.

3.31 Cleaning the petrol brush cutter

How to clean the brush cutter after use to ensure longevity.

3.32 Storing and transporting the petrol brush cutter

Proper methods for storing the brush cutter and safe transport.

3.33 Transporting and maintaining the petrol brush cutter

Details on transporting the machine and specific maintenance like lubrication and air filter.

4. Technical Characteristics

5. Troubleshooting

6. Environmental Protection

7. After sales service

8. Warranty

EC DECLARATION OF CONFORMITY

SANLI GTS26 Specifications

General

Displacement	25.4cc
Power	0.75 kW
Fuel tank capacity	0.6 L
Weight	5.8 kg
Engine type	2-stroke
Cutting Width	430 mm

Related product manuals

Preview: SANLI GTS33

Preview: SANLI BCB260