This document describes the Sanyipace Sewer Camera with 512Hz Transmitter and Detector Locator Set, Model No: F929DJTX, a specialized tool designed for inspecting pipelines and hard-to-reach areas.
Function Description
The device is primarily used for household pipeline blockage inspection, general pipe inspection, and examining underground water pipes, HVAC systems, oil and gas pipelines. It is also suitable for rescue operations in narrow spaces, underground exploration, scientific research on underwater riverbeds, and sewer system inspections. The integrated 512Hz transmitter in the camera probe allows for precise location tracking using the accompanying detector locator. The system includes a monitor for real-time viewing, recording, and playback of inspections.
Important Technical Specifications
Camera and Cable:
- Sensor: 1/3 CMOS
- Resolution: 1000TVL
- Camera Diameter: 0.9in1.7in (23mm42mm)
- Camera Type: Built-in 512Hz transmitter
- Viewable Angle: 145 degrees
- Camera Material: Stainless steel, sapphire lens, IP68 waterproof
- Camera Light Source: 12pcs 1W high white LED (adjustable)
- Cable Length Options: 66ft/20m, 100ft/30m, 164ft/50m
- Cable Diameter and Material: 0.2in (5mm) harder high elastic cable
- Transmitter Frequency: 512Hz
- Output Waveform: Sine wave
- Transmit Distance: Approximately 16.4ft (5m)
Monitor Screen:
- Size: 9-inch TFT LCD color
- Input Voltage: DC 12V
- SD Card Support: Includes 16GB card, supports max 32GB
- Display Resolution: 960*480 TFT
- Menu Language: Chinese/English
- Screen Operation: Press buttons
- Video Format: AVI
- Photo Format: JPG
- Working Temperature: -4~140°F (-20~60℃)
- Storage Temperature: -22~176°F (-30~80℃)
Battery Box:
- Charger: 100VAC-240VAC/DC 12.6V 1000MA
- Charging Time: Approximately 5 hours
- Battery: Lithium battery 12V 4500mAh
- Continuous Working Time: Approximately 6-8 hours
512Hz Detector Locator:
- Frequency: 512Hz
- Detect Distance: Approximately 16.4ft (5m)
- Battery: Built-in 3.7V 3000mAh lithium battery
- Charger: 5V 1A
- Charger Time: Approximately 6 hours
- Battery Indicator: 3 gear, flashes when low
- Battery Working Time: Approximately 10 hours
- Signal Strength: 6 gear
- Speaker: Supported
Usage Features
The system is designed for ease of use with several key features:
- LCD Monitor Operation: The 9-inch TFT color monitor provides a clear display. Buttons on the monitor allow for various functions:
- TF: Insert TF memory card for storage.
- REC/-: Start/stop video recording; confirm selection in system settings.
- **PLAY/+: **Start/pause video playback; play next video; view pictures.
- -: Take a photo; flip to next selection in system settings.
- M: Access system settings (Time/Contrast/Brightness/Colorful/Language), delete videos/pictures, or exit playback/setting mode.
- +: View pictures; back to previous selection in system settings.
- Power: Screen switch on/off.
- Counter Function: The screen automatically displays the distance the cable has traveled in both meters and feet. A "Clear key" is available to reset the counter before use. The distance is counted as the cable rotates and is displayed in real-time.
- 512Hz Transmitter and Detector Locator: The camera probe includes a built-in 512Hz transmitter that emits a signal. The detector locator receives this magnetic signal to determine the direction and position of the transmitter.
- Detection Modes: The locator features "far mode" (up to 16.4ft/5m) and "near mode" (up to 3.3ft/1m).
- Detection Process: Users start in far mode with maximum sensitivity to locate the general signal source. As they approach the strongest signal, sensitivity can be reduced. Once the strongest signal is found in far mode, switching to near mode allows for more precise pinpointing of the 512Hz transmitter's exact position.
- Cable Operation: The cable is managed via a reel. Users can pull the cable to release it or push it back to coil it by turning the handle counterclockwise or clockwise, respectively.
- Adjustable LED Lights: The camera probe is equipped with 12 adjustable 1W high white LEDs to illuminate inspection areas. Brightness can be adjusted via a button on the battery box.
Maintenance Features
- General Handling: Users are advised to handle the device with care, avoid dropping or pushing it hard. Intentional disassembly or damage voids the warranty.
- Power Management: After use, the monitor and battery should be turned off, and all connections disconnected. Avoid sudden power cuts during recording or playback to prevent damage to the product and video files.
- TF Card Management: Before inserting a TF card, it's recommended to back up any existing information to prevent data loss.
- Charging: The device charger has an indicator light (red for charging, green for fully charged). The device cannot operate if the battery power is below 20%.
- Troubleshooting Guide: The manual provides a troubleshooting section for common issues:
- No power: Check connections, battery level, and power display.
- Cannot charge: Verify DC adapter plug-in and indicator light.
- Cannot record videos: Check SD card insertion, memory, and ensure power wasn't off during recording.
- Black and white videos: Adjust LED light brightness for clearer, more colorful display.
- No signal/blue screen: Turn off/on to reconfirm, check cable connections, and slowly adjust camera probe to check for looseness.
- LED lights not working: Adjust LED brightness, tighten/loosen camera probe, check battery charge, and use a voltage tester on connectors if needed, then contact Sanyipace for damaged parts.
- Warranty and Support: Sanyipace offers a one-year product quality warranty and free lifetime technical support. Free replacement or repair services are provided for normal faults within the warranty period. Damage due to manual operation incurs a charge for parts. Technical support is available 24/7. Contact information for website, email (service@sanyipace.com, sanyimrchan@gmail.com), Facebook, and WhatsApp is provided.
To Next Page
Need help?
General
