Sanyo Denki SANUPS E11A Series User Manual (English)

Other manuals for Sanyo Denki SANUPS E11A Series

Questions and Answers:

L
larryrobersonAug 14, 2025
What to do if Sanyo Denki SANUPS E11A UPS has no output power?
- M
  Mary MooreAug 14, 2025
  If your Sanyo Denki UPS has no output power, several things could be the cause. First, ensure the input wiring is correctly connected and that the input voltage and frequency are within the rated range. Second, check that the MAIN SW is set to “ON”. Third, verify that the output voltage is set correctly in the User Settings Guide. Lastly, the bypass breaker may be tripped and need to be reset.
S
Sara HuntAug 18, 2025
Why does Sanyo Denki UPS switch to battery frequently?
- J
  Julia GomezAug 18, 2025
  If your Sanyo Denki UPS switches to battery power frequently, check whether the MAIN SW on the back panel is set to 'ON'. Also, verify that the input voltage and input frequency are within the rated limits.
L
Lisa WhiteAug 21, 2025
Why does Sanyo Denki UPS output stop during outage?
- J
  Jesus AllenAug 21, 2025
  If the output power from your Sanyo Denki UPS stops during a power outage, the battery may have deteriorated. Check the battery's condition and consider replacing it earlier than scheduled.
N
Nancy GonzalezAug 25, 2025
What to do if Sanyo Denki UPS output won't stop?
- T
  Timothy HayesAug 25, 2025
  If the output power from your Sanyo Denki UPS doesn't stop, ensure that the power button is pressed for at least 1 second to initiate shutdown. Also, check the 'UPS Shutdown Operation' setting in the user setting menu, as it may be set to '3 seconds' or 'Special operation'. Finally, verify the 'UPS Operation at OFF' setting in the user setting menu; it might be set to 'Bypass'.
E
Edward HillAug 27, 2025
How to fix Sanyo Denki SANUPS E11A buzzer and blinking light?
- S
  scotttheresaAug 27, 2025
  If the buzzer sounds and the “Green BATT.TEST” light blinks when your Sanyo Denki UPS starts, check that the battery connectors are connected properly. Stop the UPS and firmly connect the battery connectors.
D
Denise RichardsAug 30, 2025
How to turn on alarm on Sanyo Denki SANUPS E11A?
- D
  David MooreAug 30, 2025
  If the alarm buzzer on your Sanyo Denki UPS does not sound, the alarm buzzer sound may be set to “OFF”. Check the setting of “Buzzer Sound” in the user setting menu.
A
Angela WrightSep 3, 2025
Why won't my Sanyo Denki SANUPS E11A UPS restart automatically?
- M
  Melissa ThompsonSep 3, 2025
  If your Sanyo Denki UPS doesn't automatically restart after a shutdown due to battery exhaustion following a power outage, check the setting of 'UPS Operation Upon Power Recovery' in the user setting menu. Automatic UPS restart does not occur if this item is set to 'OFF'.
H
hansenabigailSep 6, 2025
How to switch Sanyo Denki UPS from bypass?
- M
  Mallory JonesSep 7, 2025
  If your Sanyo Denki UPS does not switch from bypass power supply to UPS power supply, check that Forced Bypass is set to 'Inverter'.
D
David ReevesSep 10, 2025
How to fix Sanyo Denki UPS serial communication failure?
- B
  Billy MckinneySep 10, 2025
  If serial communication fails when using the power management software with your Sanyo Denki UPS, check that 'Interface' in the user setting menu is set to 'Workstation'. Also, verify the setting of 'Serial Baud Rate'.

Sanyo Denki SANUPS E11A Series Specifications

General

Model	SANUPS E11A Series
Type	Line Interactive
Input Frequency	50/60 Hz
Output Frequency	50/60 Hz
Operating Humidity	20% to 90% (non-condensing)
Battery Type	Sealed Lead Acid
Backup Time	Varies by model and load (e.g., 5-30 minutes at half load)
Communication Interface	USB, RS-232
Operating Temperature	0°C to 40°C
Dimensions	Varies by model
Weight	Varies by model

Related product manuals

SANUPS E11A102U001-00

50 pages

Sanyo Denki SANUPS E11A Series User Settings Guide

Other manuals for Sanyo Denki SANUPS E11A Series

Questions and Answers:

Sanyo Denki SANUPS E11A Series Specifications

Related product manuals