APPEN DIX
In the event LCD
W does not work, before calling
your
dealer
or service center for assistance,
please
confirm the
following.
1 . Make sure
you
have
connected
the LCD TV to
your
equipment as described in the section
"CONNECTING
LCD
TV"
2. Check cable connections.
Verify that all external equipment and
power
cords
are
properly
connected.
3. Verify that all
power
is
switched
on.
4. lf
your
LCD TV still does not
produce
an
image, re-start the external
equipment.
5. lf an image still does
not
appear,
unplug the LCD W
from
the external equipment
and
check the equipment.
The
problem
may be with
your graphics
controller
rather than with the LCD TV.
(When you
reconnect the LCD
TV,
remember to tum the external
equipment and TV off before
you power
up the LCD TV. Power the equipment back
on
in
order
of : LCD TV then external equipment.)
6.
lf the
problem
still exists, check the
following chart.
WARNING:
High voltage
is
used to operate
this LCD TV Do not aftempt to open the cabinet.
lf
the
problem
still
persists
after
following
all operating
instructions, contact the
sales dealer
where
you
purchased
the LCD TV or an authorised
service center. Give the model number and explain the difficulty. We will advise
you
on how to obtain service.
,ry'g.!,,,F
Tt
these Solutiona
Plug the LCD
TV
into the
AC
oullet.
Press
POWER button on SIDE Control or on Remote Control to tum on the LCD TV.
Check the
POWER Indicator. lf the indicator flashes, it
indicates the LCD
TV has
a
problem.
R6mo; Controt
]aoP*]'i|ibtwo*.:=
.:
I:
Check
the batteries.
Make sure
nothing is
obstructing
the Remote Receiver
and the Remote Control.
Make sure
you
are nol too
far from the LCD TV when
using the Remote Control.
Maximum operating range is
16.4'(5m).
ls direct sunlight or strong artificial
light
shining on
the
LCD TV
's
Infrared Remote
Receiver?
Eliminate
the light source by closing curtains,
pointing
the light in
a different
direction, etc.
Check
connections between extemal eauipment and the LCD TV.
When turning the
LCD TV
on,
it
takes a
few
seconds to display the image.
Check
the system that
you
select conesponds with the external equipment or the video
equipment.
Make sure the temperature
is not
out of the operating iemperature range
(5"C
-
35"C).
Turn
off
power,
then turn on again, re-start the LCD TV.
N"#;'
:;
... i.
:
;':
il
:
Check audio cable connection
from
audio
input
source.
Adjust
the audio source.
Press VOLUME
(+)
button.
Press MUTE button.
::
::aaa:a::
::
a:::aa= . :aaaa=.:::a,ai:
::: :::::: ::::t-:::::
tfrotoef€dnY:
,-]*t*,:ls__ii
i7li
anclor ongEr
uoinls oa
urC
n
.;,.;
"'
,,
:
:.;:i
..; ..
i-
lir
i.r
Dark
or bright
points
of light
Ged,
green,
or blue) may appear
on the
screen. This is a
characteristic of the LCD
panel,
not a malfunction of the
LCD ry.
LCD
panels
are
produced
with very
high
accuracy technology. There is 99.99% or more dot
pixel,
but there
is
also 0.01 % or
les of dot
pixel
lack or dot
pixel
that
is
constantly
lighted. This is not a
defect.
Regarding
LCD
panel
characteristics,
(look
like a mirror) when
the screen is changed
if it displays
same
screen for a long time. Changing the
picture
or turn-off the
power
supply
may recover.
Stripe
pattem (more,
interference
stripes)
may show
up on the screen depend on the
reflected
Dicture.
Abro{rrtdiilraqi
Cdour
Ad.just colour settings.
Select
a different colour system.
48
To Next Page
Loading...
