Sartorius Stedim Biotech Biostat RM 200 Rocker User Manual

84 pages

To Next Page

85037-547-60

Operating Manual

Biostat

RM 200 Rocker

124.000 | 124.001

Fermenter | Bioreactor

*** TeDIS Valid on Date Printed Printed on: 20-09-2023 11:08:57 ***

185013007863

Table of Contents3
About this Document6
Validity7
Accompanying Documents7
Symbols Used8
Abbreviations8
Safety Precautions9
General Safety Precautions9
Informal Safety Measures9
Symbols Used on the Device10
Intended Use and Foreseeable Misuse11
Residual Risks from Use of the Unit12
Danger Due to Electrical Power12
Danger Due to Components under Pressure13
Danger Due to Gases14
Danger Due to Escaping Materials15
Danger Due to Hot Surfaces15
Danger Due to Moveable Components15
Danger Due to Use of Incorrect Consumables16
Hazards Due to Improper Safeguarding or Movement of the Device16
Hazards Due to System Failures16
Hazards Due to Non-Compliance with the Maintenance and Calibration Intervals16
Safety and Protective Systems17
Main Switch17
On / off Switch for the Power Supply17
Overheating Protection17
Personal Protective Equipment18
Emergency Instructions19
Operator Responsibilities19
Personnel Requirements20
Personnel Qualification Requirements20
Personnel Responsibilities21
Responsibilities21
Unauthorized Personnel21
Instruction22
Device Description23
Operation23
Variants of the Control Unit24
Temperature Control24
Setup25
Front View25
Rocker Platform - Top View26
Rear View26
Connections (Left and Right Sides of the Device)27
Device Components28
Rocker Platform / Guide Rails28
The Hood of the Device28
Aeration28
Temperature Regulator29
Filter Heater30
Load Cell (Optional)30
Sensors31
Surface Temperature Sensor31
DO and Ph Sensors31
Equipment Supplied31
Culture Bags Flexsafe RM32
Transport33
Ambient Conditions During Transport33
Shipping Instructions33
Inspection Upon Acceptance by the Recipient34
Reporting and Documenting Transport Damage34
Checking Completeness of the Delivery34
Packaging34
Setup35
Delivery Check35
Acclimatizing the Device36
Ambient Conditions36
Work Area Preparation36
Work Surfaces and Loads36
Laboratory Energy Sources37
Setting up the Device41
Remove the Transport Lock (Devices with Load Cells)41
Setting up the Control Unit41
Getting Started42
Installation Kit42
Connecting the Hood of the Device42
Connecting the Load Cells42
Connecting the Temperature Control43
Connecting the Heating Plates43
Connecting the Heating / Cooling Plates43
Connecting the Surface Temperature Sensors45
Connecting the Compressed Air and CO 2 Feeds46
Connecting the Device to the Power Supply46
Connecting the Device to the Control Unit47
Turning the Device on and off47
Preparing and Running the Process48
Overview48
General Notes on Running the Process48
Installing Culture Bags49
Placing the Culture Bag in the Rocker Platform49
Assembling the Filter Heaters with the Culture Bag50
Connecting the Aeration System to the Culture Bag51
Inflating the Culture Bag51
Connecting the Ph and DO Sensors52
Filling the Culture Bag with Culture Medium53
Setting the Cultivation Parameters and Starting Cultivation54
Cultivation Parameters (Overview)54
Turning the Device on54
Selecting the Unit (Twin Variant of Control Unit)55
Setting the Cultivation Parameters56
Process Monitoring57
Sampling and Inoculation58
Preparing for Sampling or Inoculation58
Inoculation59
Sampling59
Completing the Process, Cell Harvesting and Shutting down the Device60
Malfunctions61
Safety Instructions61
Troubleshooting61
Breakdown of Communication between Device and Control Unit62
Hardware-Related Faults63
Troubleshooting Table "Contamination63
Troubleshooting Table "Tempering64
Troubleshooting Table "Tempering Module65
Alarm Messages66
Cleaning and Maintenance67
Preliminary Steps68
Cleaning68
Maintenance69
Device Servicing by Operating Personnel69
Device Servicing by the Operator70
Device Servicing by Authorized Personnel71
Storage72
Disposal73
General Notes73
Hazardous Materials73
Decommissioning the Unit74
Disposing of the Device75
Technical Specifications76
Dimensions and Weights76
Electrical Characteristics76
Biostat ® RM 200 Rocker / 124.00076
Biostat ® RM 200 Rocker / 124.00176
Aeration77
Measurement and Control Ranges77
Rocker Function77
Temperature Control77
Measurement of Ph- and DO Values78
Device Components78
Filter Heater78
Heating Plate78
Heating / Cooling Plate78
Load Cell78
Surface Temperature Sensor79
Acoustic Emission79
Ambient Conditions79
Minimum Distances79
Consumables79
Accessories79
Conformity & Licenses80
Appendix82
Service82
Decontamination Declaration82

Need help?

Do you have a question about the Sartorius Stedim Biotech Biostat RM 200 Rocker and is the answer not in the manual?

Sartorius Stedim Biotech Biostat RM 200 Rocker Specifications

General

Brand	Sartorius Stedim Biotech
Model	Biostat RM 200 Rocker
Category	Laboratory Equipment
Language	English

Related product manuals

BioWelder Total Containment

Sartorius Stedim Biotech 16249

28 pages

Sartorius Stedim Biotech Biostat RM 200 Rocker User Manual

Table of Contents

Sartorius Stedim Biotech Biostat RM 200 Rocker Specifications

Related product manuals