Savant Video Input IP Transmitter QRG | 009-1604-03 45 Perseverance Way, Hyannis, MA 02601
Copyright 2021 Savant Systems, Inc. | 210416 1 of 2
Savant.com | 508.683.2500
Savant® ProAV Video 8 or 4 Input IP Transmitter 4K UHD with Audio Processing
and Control [PAV-VIMAP8S/PAV-VIMAP4S]
Quick Reference Guide
Box Contents
(1) Audio/Video over IP Switch
(PAV-VIMAP8S-xx/PAV-VIMAP4S-xx)
(1) Installation Kit (075-0192-xx/075-0197-xx)
(2) Standard 3U Rack Mounting Brackets (071-0638-xx)
(4) M5 x 8 mm Flat-head Phillips Screws (039-0180-xx)
(1) 4 ft Power Cord (064-0443-xx N. America)
or 4ft Power Cord (International. Can vary.)
(16 or 8) 3-pin Control Connectors (028-9351-xx)
(1) Product Regulatory Insert (009-1950-xx)
Compliance
Safety and
Emissions
FCC Part 15 CE C-Tick ETL
RoHS Compliant
Supported Releases
PAV-VIMAP8S-00
da Vinci 8.8 and higher
PAV-VIMAP4S-00
PAV-VIMAP8S-10
da Vinci 9.3.4 and higher
PAV-VIMAP4S-10
Power
Input Power 100-240V AC 50/60Hz, (5A maximum)
Nominal Power
N. America - 144VA - (1.2 A @ 120V AC, 60Hz)
International - 156VA - (.68 A @ 240V AC 50Hz)
Maximum Power
N. America - 400VA - (4 A @ 120V AC, 60Hz)
International - 432VA - (1.8 A @ 240V AC 50Hz)
Power Cable IEC320 C13 three-pole detachable power card.
Dimensions and Weights
Height Width Depth Weight
Device
5.21 in
(13.23 cm)
17.30 in
(43.94 cm)
14.24 in
(36.17 cm)
14.5 lb
(6.59 kg)
Shipping
22.0 in
(55.88 cm)
22.0 in
(55.88 cm)
10.0 in
(25.4 cm)
18.25 lb
(8.27 kg)
Rack Space 3U
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Cooling 70 cubic feet per minute (CFM) recommended.
BTU 1365 BTU/hr
Specifications
Required Components
– Savant Audio/Video over IP Device
– Savant System Host
– Savant qualified 10G Managed Network Switch
– Savant User Interface (Pro App)
– Savant Development Environment (SDE)
A
B
C D
E
Item Description
On / O
Button
Reboots the main board (MCU) and power
cycles the IP Video transmit (Tx) cards
Reset Button
Press and Release: Resets the IP Video transmit
(Tx) cards.
Press and hold: Clears the network settings.
Press and hold button for 5 seconds until Sta-
tus LED blinks red rapidly; then release.
Power LED
Green: Main board is powered.
Amber: FPGA is currently being updated.
O: Device is o. No power applied.
Status 1 LED
Green: Host has established communications
with the embedded system.
Green Blinking: Embedded system is ready, but
no communication has been established with
the host.
Amber: Host is updating the embedded
firmware.
Amber Blinking: Embedded system has a valid
link local IP address and is connecting to the
host.
Red: Host has determined the firmware needs
to be updated, but a problem occurred during
the process that will initiate a reset.
Red Blinking: Embedded firmware is running,
but has not received a DHCP IP address.
O: Embedded processor is resetting, or is
powered up, and is booting the embedded
firmware.
Hardware Failure: If a hardware failure occurs,
the status LED indication will be interrupted
every three seconds with a solid red indication.
For example, If the LED is blinking green when
a hardware failure occurs, the LED will
alternate between blinking green and solid red
at three-second intervals.
Status 2 LED Reserved for future use.
A
B
C
D
E
Network Requirements
For more information, see the Savant Device Networking Guidelines on
the Savant Customer Community.
Front Panel
Additional Information
Refer to the following documents located on the Savant Customer
Community for additional information.
– Savant Video over IP Deployment Guide (009-1551-xx)
– Savant Video over IP Network Configuration Guide (009-1552-xx)
– Savant IP Audio Deployment Guide (009-1571-xx)
To Next Page
Need help?
General
