PAV-VOM1CP2 Quick Reference Guide | 009-2034-00
Copyright 2021 Savant Systems, Inc | 210430
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 2
Box Contents
(1) Single Video IP Receiver (PAV-VOM1CP2-xx)
(1) Installation kit (075-0210-xx)
(1) Power Adapter with International Clips (025-0195-xx)
(1) Internation Clips (CN, US, UK, EU & AUS)
(2) Mounting Brackets (071-1093-xx)
(4) M2.5 x 4mm screws (for mounting brackets) (039-0590-xx)
(1) IR Emitter (4ft long) (064-0442-xx)
(1) 3-pin RS232 Control Connector (028-0805-xx)
(1) Product Information and Regulatory Statement (009-1950-xx)
Specifications
Environmental
Temperature 30° to 105° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weights
Height Width Depth Weight
Device
6.97 in
(17.7 cm)
5.91 in
(15.0 cm)
1.00 in
(2.54 cm)
1.35 lb
(0.61 kg)
Shipping
16.0 in
(40.64 cm)
9.00 in
(22.86 cm)
4.00 in
(10.16 cm)
3.00 lb
(1.35 kg)
Power
Power over
Ethernet (PoE+)
IEEE 802.3at
Input Power 12V 2A DC
Nominal Power 16 W
Maximum Power 24 W
1 = at 24 Hz
2 = at 25 Hz
3 = at 30 Hz
4 = at 50 Hz
5 = at 60 Hz
Video
HDR Supported
Supported
Formats
640x480
5
720x480
6
720x576
4
800x600
5
1024x768
5
1280x720
4
1280x720
5
1280x1024
5
1920x1080
1
1920x1080
3
1920x1080
4
1920x1080
5
1920x1200
5
3840x2160
1
3840x2160
2
3840x2160
3
3840x2160
4
3840x2160
5
4096x2160
3
4096x2160
5
Audio
Supported
Formats
Pass-though of all HDMI 2.0 audio formats are
supported.
Compliance
Safety and
Emissions
FCC Part 15 CE C-Tick
RoHS Compliant
Supported Releases
Software
Release
da Vinci 9.4 and higher
Network Configuration
To ensure that the IP Address will not change due to a power outage,
Savant recommends using DHCP reservation within the router. By
using this method IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE: Setting DHCP reservation varies from router to router. Refer to
the documentation for the router to configure DHCP reservation.
Front Panel
A
Power LED
O - Device is o. No power applied
Red - Main board is powered
B
Video LED
O - No video signal detected
Blue - Video signal detected
C
LinkTX LED
O - No valid connection
Blue - Valid link
Blinking - Sending Ethernet Data
D
LinkRX LED
O - No valid connection
Blue - Valid link, not receiving Ethernet Data
Blinking - Receiving Ethernet
E
Status
Blue - Reset button is pressed when the
device is powered on
Blinking - Reset button has been released or
the device was powered on without holding
the reset button
F
P1 Reserved for future use.
Reset
Hold down this button with a pointed
stylus for 20 seconds while powering up
the device to restore the device to factory
default settings
Power Video LinkTx LinkRx Status
P1 Reset
B
C
D
E
F
G
A
Network Requirements
For more information, see the Savant Device Networking Guidelines
on the Savant Customer Community.
Required Components
– Savant Audio/Video over IP Device
– Savant System Host
– Savant qualified 10G Managed Network Switch
– Savant User Interface (Pro App)
– Savant Development Environment (SDE)
Savant® IP Video Single Output Receiver 4K UHD with Control (PAV-VOM1CP2)
Quick Reference Guide
To Next Page
Need help?
General
