How to clear 'Cover open' error on Sbarco Label Maker?
The 'Cover open' error on your Sbarco Label Maker means that the printer cover is not closed properly. Simply close the printer cover to clear the error.
Why does my Sbarco T4 Label Maker say 'Ribbon out'?
If your Sbarco Label Maker displays 'Ribbon Out', it could be due to two reasons: * The ribbon roll has run out: Reload a new ribbon roll. * The ribbon roll isn't loaded correctly: Ensure the ribbon supply and take up core are fixed correctly.
How to fix 'Label gap out' error on my Sbarco T4 Label Maker?
If your Sbarco Label Maker displays 'Label gap out', it could be due to several reasons: * **Improper sensor type**: Ensure the sensor type, reflective or see-through, is selected correctly. * **Label sensor cable issue**: Reconnect or tighten up the sensor cable if it's disconnected or loose. * **Dirty sensor windows**: Clean the receiver sensors and emitter sensor. * **Improper media sensor position**: Adjust the media sensor to the correct position. * **Incorrect label type setting**: Load the correct media or set the label type to the current media type.
What to do if Sbarco T4 Label Maker shows 'Update fail'?
If your Sbarco Label Maker displays 'Update fail', the firmware update has failed. In this case, try re-updating the firmware.
Why does my Sbarco T4 Label Maker show 'Check sum error'?
If your Sbarco Label Maker displays 'Check sum error', it indicates that the firmware update has failed. To resolve this, re-update the firmware.
What to do if Sbarco T4 displays 'TPH fail'?
If your Sbarco Label Maker displays 'TPH fail', it could be due to: * A disconnected TPH cable: Connect the TPH cable. * A faulty or damaged TPH: Replace it with a new TPH.
What to do if my Sbarco Label Maker says 'Cutter jam'?
The 'Cutter jam' error on your Sbarco Label Maker indicates that the cutter is experiencing a jam during printing. To resolve this, inspect the cutter area to see if any labels are stuck and clear them.
What does 'Update fail' mean on Sbarco T4?
The 'Update fail' error message on your Sbarco Label Maker indicates that the firmware update has failed. To resolve this, try re-updating the firmware.
Why does my Sbarco T4 say 'Label out'?
The 'Label out' error on the Sbarco Label Maker means that the label roll has run out. To fix this, simply reload a new media roll into the label maker.
How to fix 'Label gap out' error on Sbarco T4?
The 'Label gap out' error on your Sbarco Label Maker can occur due to several reasons. First, ensure that the correct sensor type (reflective or see-through) is selected. Check the label sensor cable to ensure it is securely connected. Dirty sensor windows can also cause this issue, so clean the receiver and emitter sensors. Verify that the media sensor is correctly positioned. Finally, if you are using a continuous label, make sure the label type setting matches the media type.
Lists the essential components included with the printer package.
Introduces the features of the T4 printer model.
Illustrates and labels the front-facing components of the T4 printer.
Illustrates and labels the rear-facing ports and connectors of the T4 printer.
Illustrates and labels the internal components and mechanisms of the T4 printer.
Introduces the features of the T4e printer model.
Illustrates and labels the front-facing components of the T4e printer.
Illustrates and labels the rear-facing ports and connectors of the T4e printer.
Illustrates and labels the internal components and mechanisms of the T4e printer.
Step-by-step guide on how to properly install the printer ribbon.
Instructions for loading the printer with various types of media rolls.
Details the various ports available on the T4 printer for PC connectivity.
Explains the connection and use of the Centronics parallel port.
Explains the connection and use of the RS-232 serial port.
Details the connection and use of the USB slave port for printer interaction.
Explains the optional Ethernet connection for network capabilities.
Details the various ports available on the T4e printer for PC connectivity.
Explains the connection and use of the USB slave port on the T4e.
Explains the optional Ethernet connection for the T4e printer.
Step-by-step instructions on how to safely power on the printer.
Explains the functions of buttons and indicators on the T4 printer's control panel.
Explains the functions of buttons and indicators on the T4e printer's control panel.
Guide for installing the optional peeler accessory on the printer.
Instructions for installing the optional cutter accessory on the printer.
Details the various parts of the LCD screen and their meanings.
Explains the meaning of different symbols displayed on the printer's LCD screen.
Outlines the hierarchical structure of the printer's menu system.
Covers various settings and configurations for printer operation.
Configuration options related to user preferences and system settings.
Settings for establishing communication interfaces like RS-232 and Ethernet.
Parameters for configuring printing modes, speed, darkness, and label types.
Functions for testing printer configurations, patterns, and cutter operation.
Management of stored forms, images, and fonts in memory devices.
Instructions for running stored forms and setting auto-form recall.
Lists common warning icons and their corresponding error messages.
Describes the status icons displayed by the printer and their meanings.
Lists common error messages displayed on the LCD and their resolutions.
Detailed technical specifications for the T4 and T4e printer models.
Diagrams and pin assignments for USB A (Master) and USB B (Slave) ports.
Pin assignment details for the serial port on the printer.
Pin assignment details for the Ethernet module connector.
Guide to operating the printer independently using a keyboard or scanner.
General| Brand | Sbarco |
|---|---|
| Model | T4 series |
| Category | Label Maker |
| Language | English |
To Next Page
