7
Operation / Work Instructions
Caution! For your safety, the machine must be held
only at the two handles (3 and 4, Figure 1)!
This will avoid the danger of an electric shock through
contact of lines during chiselling.
Switching on / off (Fig. 4)
Switching on: Press the operating switch (3).
Switching off: Release the operating switch (3).
Always keep the chiselling tools sharp.
Note:
– Work only at low pressure when chiselling.
– Excessive pressure loads the motor unnecessarily.
– Sharpen the chisels in time and replace, if neces-
sary.
Electrical connection
Check power supply cables regularly for damage. Make
sure that the power cable is not connected to the mains
supply when you check.
Electrical connections must comply with the relevant
Australian regulations. Only use connecting cables with
H 07 RN mark.
An imprint of the type designation on the power cable is
mandatory.
Recommendation that the tool alway be supplied via a
residual current device with a rated residual current of
30 mA or less
Faulty power supply cables
Insulation damage often occurs at power supply cables.
Causes are:
• Pressure points when power supply cables are routed
through the window or door gaps.
• Bends due to improper fastening or guiding of the po-
wer supply cables.
• Interfaces by running over the power supply cables.
• Insulation damage by pulling off the wall outlet.
• Cracks due to ageing of the insulation.
Such defective power supply cables must not be used
and are extremely dangerous to life because of the in-
sulation damage!
AC motor 230-240 V / 50 Hz
Mains voltage 230-240 V / 50 Hz
Power supply and extension cord must be 3-wire = P + N
+ SL. - (1/N/PE).
Extension cables must have a minimum cross section of
1.5 mm².
The mains supply is secured up to 16 A.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection conditions.
This means that use of the product at any freely selec-
table connection point is not allowed.
• Given unfavorable conditions in the power supply the
product can cause the voltage to uctuate temporarily.
• The product is intended solely for use at connection
points that
ter pipes using a pipe locator.
Operation
Use only proper equipment.
• Do not force the machine or accessory not to do the
work of a larger industrial machine. It works better at
the power rating for which it was designed.
• Make all machine adjustments only with the machine
switched off.
• Never leave the machine unattended while it is run-
ning.
• When switching off, leave the machine only after it
comes to a complete standstill.
• Turn the machine off before you unplug it.
• Always unplug the mains cord. Never pull out the plug
from the wall outlet by holding the cable.
• Perform maintenance and cleaning of the device re-
gularly.
• Have the device checked, if necessary.
If you are not sure whether a working condition is
safe or unsafe, do not work with the machine.
Features Fig.1
1 Motor housing
2 Handle
3 On / Off switch
4 Additional handle
5 Tool holder
6 Locking bolt
7 Oil ll opening / sight glass
8 Point chisel
Getting started
Using the chisel Fig. 2
1 Clean chisel always before inserting it and lubricate
the shaft slightly.
2 Pull out the locking bolts (6) up to the end stop, turn
by 180° and release.
3 Insert chisel into the tool holder (5) and slide it up
to the end stop.
4 Pull out the locking bolts (6) once again, turn by
180° and release.
5 Check lock on the tool.
Remove chisel
Pull out the locking bolts (6) up to the end stop, turn by
180° and release, and remove the chisel.
Additional handle Fig.3
For safety reasons, use the demolition hammer only
with the additional handle!
1 The additional handle (4) provides you safe grip while
using the demolition hammer.
2 The additional handle (4) can be rotated to any po-
sition.
3 Loosen the Allen screw (A).
4 Turn the additional handle (3) to a convenient and
safe working position and tighten the screw (A) again.
To Next Page
Loading...
Need help?
General
