Check electrical connecting cables regularly for
damage. Ensure that when checking the con-
necting cable, it does not hang from the power
mains. Electrical connecting cables must corre-
spond to the common VDE and DIN provisions.
Use only connecting cables that have the desig-
nation H 07 RN.
An imprint of the type designation on the con-
necting cable is mandatory.
AC Motor
AC motor 230 V/ 50 Hz, mains voltage 230 Volt
/ 50 Hz.
Use of a residual current protection device (“FI“)
is recommended for a 230V connection.
If you use an extension cable, insert it directly
into the FI.
If operating it in Switzerland, insert the concrete
mixer only in sockets that are protected by a re-
sidual current-operated circuit breaker.
Mains connection and extension cable can have
3 wires as well as 2.
3-wire: P + N + SL. - (1/N/PE); 2-wire: P + N – (1/N)
Extension cables must have a minimum cross-
section of 1.5 mm².
Connecting cable, plug and coupling jack must
be protected against water spray.
The mains connection is protected with a maxi-
mum 16A fuse.
Connections and repairs of the electrical
equipment should be performed by electri-
cians only.
Please quote the following information in
your queries:
• Current type of the motor.
• Data on the machine ratings plate.
When returning the motor, always send the com-
plete drive unit with switch.
Equipment packing list Fig.1
1. Supporting stand, front
2. Motor casing
3. Frame
4. Swivel wheel
5. Drum upper section
6. Bearing bracket
7. Drum lower section
8. Instructions
9. Mixer
10. Bag provided (Fig. 2 Content)
11. Supporting stand, rear with wheel axle
12. 2 wheels
13. Locking washer
Technical data
MIX125 MIX140
Motor 230V / 50 Hz 0,55 kW 230V / 50Hz 0,55 kW
Capacity 125 l 140 l
Protection class IP45D IP45D
Dimensions 1200mm x 710mm x 1400mm 1200mm x 710mm x 1400mm
Weight 45.5 kg 47 kg
Sound pressure level L
pA
/ uncertainty K 67dB(A) / 9.8dB(A) 67dB(A) / 4.4dB(A)
Sound power level L
WA
/ uncertainty K 97dB(A) / 9.8dB(A) 91dB(A) / 4.4dB(A)
Information on noise
Warning: Noise can seriously damage your
health. If the engine noise exceeds 85 dB (A),
please wear appropriate hearing protection. If
the electrical connection is faulty, the current
may drop when the machine starts. This may af-
fect other machines (e.g. ashing lights). If the
electric output corresponds to Zmax <0.27, such
interference should not occur. (If it does, notify
your dealer).
• The vibration emission value given below has
been measured by a standardized test, and
can be used for comparing one power tool to
another;
• The vibration emission value given below may
also be used for a rst assessment of exposure.
Warning:
• The vibration emission value may vary during
actual use of the power tool from the specied
value, depending on the manner in which the
power tool is used;
• Try to keep exposure to vibration to a mini-
mum. Examples of ways to reduce vibration
levels are wearing gloves when using the
tool and limiting working hours. In doing so,
all parts of the operating cycle must be taken
into account (for example, times in which the
power tool is turned off, or when it is turned
on without load).
Unpacking
Take the concrete mixer out of the carton with the
help of two persons.
Check to ensure that the delivery is complete.
Inform the dealer if there are faults.
Montage
Caution!
The concrete mixer should be used only after it
is installed fully.
1. Installing wheels Fig.3
Install splint on both sides, washer, wheel (12),
washer, splint on the supporting stand rear with
wheel axle (11).
Bend the splints slightly after installation
2. Installing the front supporting stand with
frame Fig.4
Install front supporting stand (1) with 2 M8x70
screws, 2 8mm washers, 2 lockwashers, 2 M8
nuts on the frame (3) and tighten the screws.
3. Installing the frame with the wheel sup-
ports Fig. 5
Install frame and wheel supports fully with 2
M8x70 hexagon bolts, 2 8mm washers, 2 lock-
washers and 2 M8 nuts. Tighten the screws.
4. Installing the lower section of drum with
frame Fig.6
Set the lower section of the drum (7) with bear-
ing bracket (6) on the pre-installed framework,
tighten with 2 M8x65 hexagon bolts, 2 washers,
2 lockwashers and 2 M8 nuts.
Secure with a Ø42 spiral ring.
5. Installing mixer Fig.7
Lock mixer (9) with 2 M8x20 cross-head screws
to the lower section of the drum with 2 washers,
2 lockwashers and 2 M8 nuts. Insert one rubber
washer each between mixer and drum.
16
DGB
To Next Page
Loading...
Need help?
General
