EasyManua.ls Logo

schmersal SLC 410 - User Manual

schmersal SLC 410
23 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SLC 410 / SLG 410
PHOTOELECTRIC
SAFETY
BARRIER
SLC 410 / SLG 410
MOUNTING AND WIRING INSTRUCTIONS
TABLE OF CONTENTS
INTRODUCTION........................................................................................................................2
OPERATION...............................................................................................................................3
INSTALLATION ..........................................................................................................................4
POSITION...........................................................................................................................5
SAFETY DISTANCE CALCULATION....................................................................................6
VERTICAL POSITION OF THE BARRIER.............................................................................7
HORIZONTAL POSITION OF THE BARRIER........................................................................8
ELECTRICAL CONNECTIONS.............................................................................................9
MULTIPLE SYSTEMS........................................................................................................ 12
DISTANCE BETWEEN REFLECTING SURFACES ............................................................. 12
USE OF DEFLECTION MIRRORS...................................................................................... 14
MECHANICAL ASSEMBLY AND OPTIC ALIGNMENT......................................................... 15
OPERATION AND TECHNICAL DATA...................................................................................16
SIGNALS .......................................................................................................................... 16
TEST FUNCTION.............................................................................................................. 17
OUTPUTS STATUS ........................................................................................................... 17
TECHNICAL SPECIFICATIONS ......................................................................................... 18
DIMENSIONS ..........................................................................................................................19
CHECKS AND MAINTENANCE...............................................................................................21
TROUBLESHOOTING ....................................................................................................... 22
SPARE PARTS.........................................................................................................................23

Table of Contents

Questions and Answers

  • S
    swhiteAug 10, 2025
    What to do if Schmersal Lighting Equipment detects interfering dangerous emitter?
    • C
      Christina HillAug 11, 2025
      If your Schmersal Lighting Equipment detects an interfering dangerous emitter, locate it and then reduce the emitter range from high to low, switch the position of the Emitter and Receiver, move the interfering Emitter to avoid it illuminating the Receiver, or shield the beams coming from the interfering Emitter using opaque protections.
  • I
    Isabella GarciaAug 15, 2025
    What to do if Schmersal Lighting Equipment shows OSSD static outputs error?
    • H
      Heather Wright DDSAug 15, 2025
      If your Schmersal Lighting Equipment shows an OSSD static outputs error, for STANDARD and MASTER MODELS, carefully check the connection of terminals 1 and 3 (OSSD) on the connector. If necessary, adjust the load, reducing the current required to a maximum of 500 mA (2PF). For SLAVE MODELS, send the equipment to SCHMERSAL for repair.
  • A
    antonionicholsAug 20, 2025
    What to do if schmersal SLC 410 has OSSD1 - OSSD2 short-circuit?
    • K
      Kristopher DavisAug 20, 2025
      If your Schmersal Lighting Equipment experiences an OSSD1 - OSSD2 short-circuit, for STANDARD and MASTER MODELS, carefully check the connection of terminals 1 and 3 (OSSD) on the connector. For SLAVE MODELS, send the equipment to SCHMERSAL for repair.
  • S
    Steve NolanAug 26, 2025
    What to do if schmersal SLC 410 is overloaded?
    • T
      Thomas ThompsonAug 27, 2025
      If your Schmersal Lighting Equipment is overloaded, for STANDARD and MASTER MODELS, carefully check the connection of terminals 1 and 3 (OSSD) on the connector. If necessary, adjust the load, reducing the current required to a maximum of 500 mA (2PF). For SLAVE MODELS, send the equipment to SCHMERSAL for repair.
  • P
    Patricia HuynhAug 30, 2025
    How to restart Schmersal Lighting Equipment after user configuration change?
    • A
      adam84Aug 30, 2025
      If the user configuration of your Schmersal Lighting Equipment was changed without a system restart (only for MASTER and STANDARD models), operate a system restart.
  • M
    Maria RossSep 4, 2025
    What to do if schmersal SLC 410 Lighting Equipment has internal error?
    • J
      Jason WilliamsSep 4, 2025
      If your Schmersal Lighting Equipment has an internal error (add-on board), send the equipment for repair to SCHMERSAL.

schmersal SLC 410 Specifications

General IconGeneral
Brandschmersal
ModelSLC 410
CategoryLighting Equipment
LanguageEnglish