A) Standard
1.Press and hold button 1 and press button 2 four times at same time
2. Release 2 buttons till LED flashed once every three seconds
3. Put original remote in the front of new remote (about 2-3cm), press the
original remote button which need to be copied until the LED of new remote
flash quickly (LED have regular flashes)
4. Press the button of New remote that you want to use to save the code
5. If you do not copy successfully, please repeat above steps
6. To duplicate a second button, repeat the above steps
B) Automatic matching code
After copy successfully,don't use any remote first, then put the new remote
close to the receiver to active it, press and hold the button until the Led of it
flash quickly, then you can try it
Emitting seed code
Pressing the button 1 and button 2 at the same time until LED flashes quickly.
Release 2 buttons,press the button that you want to emit seed code, it has
emiteed seed code successfully
AMC: Automatic Matching Code
BFT
1) Press and hold button 1 and press button 2 four times at same time,Release 2 buttons till LED flashed once every three seconds
2) Put original remote in the front of new remote (about 2-3cm), press and hold the original remote button which need to be copied until the LED will turn on
with a fixed light and then emits a double flash very 2 seconds
3) Pressing the hidde button or the button 1 and 2 simultaneously in the new models (transmit the seed code of original BFT remote)
4) Now the led will flash quickly,press the new remote button that you want to save the code, the LED will off
5) Now active the remote with AMC procudure
FAAC and GENIUS
Note: your original remote conrol must be in a master version
How to recognise a master/slave transmitter:
master: if you press any key of a master transmitter, the LED flashes before becoming steady.
slave: if you press any key of a slave transmitter, the LED goes on immediately with steady light
1) Press and hold button 1 and press button 2 four times at same time,Release 2 buttons till LED flashed once every three seconds
2) Put original remote in the front of new remote (about 2-3cm), press and hold the original remote button which need to be copied until the LED will turn on
with a fixed light and then emits a double flash very 2 seconds
3) Pressing and hold the button 2 and 3 simultaneously of original FAAC/GENIUS to transmit the seed code
4)While the led of FAAC and GENIUS is flashing, put it close to new remote about 2-3cm, and press the button that you want to copy unitl the LED will change the
frequency of flash(faster than before to confirm the correct copy the code)
V2
1) Press and hold button 1 and press button 2 four times at same time,Release 2 buttons till LED flashed once every three seconds
2) Put original remote in the front of new remote (about 2-3cm), press and hold the original remote button which need to be copied until the LED will turn on
with a fixed light and then emits a double flash very 2 seconds
3) Press and hold once again the same button of original remote, the LED of new remote will flashes quickly, press the button that you want to save the code,
unitl the LED off
4) Now active the remote with AMC procudure
Compatible List
Brand Model Brand Model
ACM (AMC) TX2, TX2 COLOR, TX4 KEY 900TXB-42R,SUB44,TXB-44R,TXG-44R
ADYX TE4433H BLUE, 433-HG BRAVO KINGGATES STYLO,CLIPPER
AERF
COMPACT,HY-DOM, MERCURI B, MERCURI C, SABUTON,
MARS,SATURN, ST3/N, TERRA, TMP-1,TMP-2, UNITECH
KLING KUA,KUAE,KUA S
LABEL SPYCO, RJW4E
ALLMATIC (AMC) BROWN, BROWN RED, BRO.OVER, PASS, MINIFASS LEB TMW
APERIO GO, GO PRO, GO MINI LINCE LR2035
APERTO
(SOMMER)
TX02-434-2, TX02-868-2 BLUE, 4025 TX02-868-2, 4022 TX02-434-2,
4020 TX03-434, TX-03-868-4, 4013, TX03-434-4
LIFE
LIFE FIDO2 / FIDO4 / VIP2 / VIP4 / VIP2R / VIP4R / STAR2 / STAR4 /
BRAVO2 / BRAVO4
APRIMATIC (AMC) TR2/TR4, TM4, TXM LINEAR MCT-11,ACT-22,ACT-21,STING RAY ACT-31,STING RAY ACT-34B
ATA PTX4 BLUEM PTX4 PINK MHOUSE (AMC) GTX4, GTX4C, TX4
AVIDSEN 104251, 104250, 104250 OLD, 104250 RED, 104257, 104350, 654250
MA TX1,TX2,TX3
MOOVO (AMC) MT4G