EasyManua.ls Logo

Scosche X3 User Manual

Scosche X3
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Scosche Industries
X3 Wireless Lighter Sensor D.I.Y. Alarm
1. Including:
1 lighter shape wireless sensor (can detect door open, trunk open, glass broken & big shocking), 1 module, 2-pc transmitter
2. Installation:
a. Screw the siren in the hood and connect the siren red & black wires to battery +12 volt & ground each.
Please keep the siren a little downward to avoid the water goes in. Do not install the siren too near the engine or high
temperature area.
ATTN: 1. Keep the small black antenna wire straight & away from the steel as can to have longer range.
2. The X3 only suit for the vehicle that come with good sealing of door & trunk when closed.
b. Turn the switch on the lighter sensor to On position, then plug into the 12 volt lighter socket for charging when ignition key
is On.
3. Operation:
(1) 1
st
(Big) Button of Transmitter: Arm/Disarm
a. Press this button once can arm the system (will chirp once) or disarm the system (will chirp twice or chirp 4 times if
triggered before).
Please close all the doors & trunk well before arm the system, otherwise the system will not be triggered.
The siren will sound 3 times 30 seconds for any door open/trunk open/ glass broker/ big shocking when armed.
Press this button once can stop the sounding if siren is triggered and system will still keep armed, must press button once
again to disarm the system.
Remark: The lighter sensor can be hided in the glove box or inside of car where still can detect the air flow when door of
trunk is open (when not in charging) that still can be triggered if all the doors & trunk closed well when armed.
b. Transmitter & Lighter Sensor Code-Learning:
Within the 8 seconds after connected the white wire(code learning wire) to ground once, trigger the lighter sensor (toward
the sensor blowing by mouth if sensor switch is on, or switch on the sensor from off) or press the transmitter button once
can learn the sensor or transmitter code into the siren. Will chirp once if 1
st
code is learned, chirp twice for 2
nd
code and so
on, max. total 4 sets code can be learned.
Suggest to learn all the lighter sensor & transmitter codes into the siren if to do the code-learning.
The code-learning will be end immediately after the last set 4
th
code learned.
ON 0FF
Question and Answer IconNeed help?

Do you have a question about the Scosche X3 and is the answer not in the manual?

Scosche X3 Specifications

General IconGeneral
BrandScosche
ModelX3
CategoryAccessories
LanguageEnglish

Summary

Installation

Siren and Antenna Installation

Details installing the siren, connecting wires to battery, and antenna placement for optimal range.

Lighter Sensor Connection

Explains how to connect the lighter sensor by turning its switch on and plugging it into the 12V socket.

Operation

Transmitter Main Button (Arm/Disarm)

Details using the transmitter's big button to arm/disarm the system and stop the siren.

Transmitter Second Button (Panic)

Describes using the second transmitter button for the panic function and for arming/disarming.

Code-Learning Procedure

Explains the procedure for learning transmitter and sensor codes into the siren, supporting up to four codes.

Optional Sensors

Shock and Voltage Drop Sensor Modes

Describes how to enter sensor setting mode and select between shock sensor, voltage drop sensor, or both.

Saving Sensor Settings

Explains how to save the selected sensor mode and exit the setting mode.

Shock Sensor Sensitivity Setting

Entering Sensitivity Setting Mode

Details how to enter the shock sensor sensitivity setting mode.

Adjusting Sensitivity Levels

Explains how to adjust the shock sensor sensitivity through 8 levels and test its trigger response.

Saving Sensitivity Settings

Describes how to save the adjusted sensitivity level and exit the setting mode.