EasyManua.ls Logo

Sea-doo SWITCH 16 2024 - Page 140

Sea-doo SWITCH 16 2024
252 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
138
NNOOTTIICCEE
AAnn oobbjjeecctt oorr ttooooll ccaauugghhtt iinn tthhee iiBBRR
ssyysstteemm wwhheenn uussiinngg tthhee iiBBRR oovveerr--
rriiddee ffuunnccttiioonn mmaayy ccaauussee ddaammaaggee
ttoo tthhee iiBBRR ccoommppoonneennttss.. RReemmoovvee
aallll rriiggiidd ffoorreeiiggnn oobbjjeeccttss tthhaatt mmaayy
oobbssttrruucctt tthhee iiBBRR ggaattee ttrraavveell bbeeffoorree
mmoovviinngg iitt..
WWAARRNNIINNGG
IIff iitt iiss nneecceessssaarryy ttoo rreeaacchh iinn ttoo rree--
mmoovvee aannyy ffoorreeiiggnn oobbjjeecctt ccaauugghhtt iinn
tthhee pprrooppuullssiioonn ssyysstteemm,, ssttrriiccttllyy oobb--
sseerrvvee tthhee ffoolllloowwiinngg bbeeffoorree
pprroocceeeeddiinngg::
RReemmoovvee tteetthheerr ccoorrdd ffrroomm tthhee
eennggiinnee ccuutt--ooffff sswwiittcchh..
WWaaiitt aatt lleeaasstt 55 mmiinnuutteess..
DDoo nnoott pprreessss oonn SSTTAARRTT//SSTTOOPP
bbuuttttoonn.. SShhoouulldd tthhee SSTTAARRTT //
SSTTOOPP bbuuttttoonn bbee pprreesssseedd,, wwaaiitt
aannootthheerr 55 mmiinnuutteess..
AAccttiivvaattiinngg iiBBRR OOvveerrrriiddee FFuunnccttiioonn
1. Power up the electrical system by
pressing the START/STOP button.
2. Install the tether cord on the en-
gine cut-off switch.
NNOOTTEE:: The tether cord must be in-
stalled to ensure the information cen-
ter will not shut off all indications after
its self test function. Electrical power
will stay on for approximately 1 hour.
3. Pull in and hold the iBR lever for
the entire procedure.
1. iBR lever pulled and held
4. When the IIBBRR OOVVEERRRRIIDDEE --
PPRREESSSS MMOODDEE BBUUTTTTOONN mes-
sage appears in the multifunction
gauge, press the MODE button.
When the function is activated, a
ON message will be shown.
5. While still holding the iBR lever in,
press the VTS UP/DOWN button
to move the iBR gate to the de-
sired position. Ensure the VTS in-
dication in the multifunction gauge
changes with the iBR gate move-
ment. If the iBR gate moves up-
wards, the indication moves
upwards.
6. Release the iBR lever.
7. Remove the tether cord from the
engine cut-off switch.
WWAARRNNIINNGG
IIff iitt iiss nneecceessssaarryy ttoo rreeaacchh iinn ttoo rree--
mmoovvee aannyy ffoorreeiiggnn oobbjjeecctt ccaauugghhtt iinn
tthhee pprrooppuullssiioonn ssyysstteemm,, ssttrriiccttllyy oobb--
sseerrvvee tthhee ffoolllloowwiinngg bbeeffoorree
pprroocceeeeddiinngg::
RReemmoovvee tteetthheerr ccoorrdd ffrroomm tthhee
eennggiinnee ccuutt--ooffff sswwiittcchh..
WWaaiitt aatt lleeaasstt 55 mmiinnuutteess..
DDoo nnoott pprreessss oonn SSTTAARRTT//SSTTOOPP
bbuuttttoonn.. SShhoouulldd tthhee SSTTAARRTT //
SSTTOOPP bbuuttttoonn bbee pprreesssseedd,, wwaaiitt
aannootthheerr 55 mmiinnuutteess..
SPECIAL PROCEDURES

Related product manuals