EasyManua.ls Logo

Seacraft ENC II - User Manual

Seacraft ENC II
70 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1

Table of Contents

Questions and Answers

  • M
    Matthew BenderAug 13, 2025
    Why is my Seacraft ENC II compass showing improper heading?
    • C
      cgoodAug 13, 2025
      If your Seacraft GPS compass shows an incorrect heading, there might be several reasons. First, try calibrating the device as described in chapters 13.1 and 13.2. If that doesn't work, a strong external magnetic field near the device could be the cause; attempt to remove any magnetic elements from the vicinity or move the device to another location. As an additional option, the compass sensor might have been overcharged; power off the device, wait 10 seconds, connect the charger for 10 seconds, and then check the compass again. If none of these steps resolve the issue, the sensor may be defective, requiring you to return the device for service.
  • B
    bryanlorettaAug 17, 2025
    How to fix Seacraft GPS device that cannot be switched on?
    • R
      Ricardo HeathAug 17, 2025
      If your Seacraft GPS device isn't switching on and the display is blank, it might be due to excessive battery discharge. Try charging the battery for at least 30 minutes; the red LED should start blinking after a few minutes. If the device still doesn't respond and you suspect it's broken (e.g., flooded or charged from an improper source), factory service is needed.
  • B
    Brandi WallaceAug 20, 2025
    Why does my Seacraft ENC II GPS battery charge level never reach 90%?
    • M
      Madeline PerryAug 20, 2025
      If your Seacraft GPS isn't charging fully and the battery charge level never reaches 90%, it could be due to several reasons. The battery might be broken, requiring you to return the device for service. Alternatively, the charging cable may be damaged or the connector might be dirty or rusty; try cleaning the charger connector and ensure it's not damaged. Lastly, the charging source might be too weak; try using a different charger, such as the USB port of a laptop or PC.
  • A
    Angela WoodAug 25, 2025
    What to do if Seacraft ENC II shows 'Battery is low!' message?
    • D
      Dr. Justin Fowler MDAug 25, 2025
      If your Seacraft GPS shows a 'Battery is low!' message and switches off, it means the battery is discharged too much. To resolve this, simply charge the device.
  • M
    Melanie RamseyAug 27, 2025
    Why is my Seacraft ENC II GPS switching on and off continuously?
    • D
      Diana LeachAug 28, 2025
      If your Seacraft GPS is switching on and off continuously, it could be due to a damaged internal sensor or a broken battery. Try connecting the charger for 1 minute. If this doesn't help, allow the device to fully discharge and switch off. Wait 1 hour, then try charging it again. If the issue persists, return the device for service.
  • T
    Tracy CarlsonSep 1, 2025
    What to do if Seacraft GPS depth indication is 0?
    • C
      Christopher SmithSep 1, 2025
      If your Seacraft GPS depth indication is stuck at 0 and never changes, indicating an invalid depth, it suggests a defective pressure sensor. To confirm this, go to Settings / Pressure/salin. If the pressure reading is near 0, the sensor is indeed defective, and factory service is needed.
  • P
    Paul DelgadoSep 4, 2025
    How to fix Seacraft ENC II GPS not switching on in water?
    • K
      Kimberly PayneSep 4, 2025
      If your Seacraft GPS is not switching on automatically when immersed in water, it might be because the pressure sensor gap is filled with dirt or mud. Wash the device using a mild stream of warm fresh water until the problem is resolved.
  • D
    Donald MillerSep 8, 2025
    Why does my Seacraft ENC II GPS external sensor not show speed?
    • B
      Bobby HuntSep 9, 2025
      If the external sensor is connected to your Seacraft GPS, but no speed is shown, it could be due to a sensor connector issue or the device's operation mode. First, disconnect the sensor plug, wash and/or clean the connector, and then reconnect it. If the problem persists, go to Settings / Log/Speed and ensure that EXT is set to ‘Active Log’.

Seacraft ENC II Specifications

General IconGeneral
BrandSeacraft
ModelENC II
CategoryGPS
LanguageEnglish