EasyManua.ls Logo

Sealey CM4 - User Manual

Sealey CM4
2 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SET OF 4 CORNER TRANSPORT DOLLIES
150KG CAPACITY
MODEL NO: CM4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, and local authority regulations are adhered to when assembling and using this corner moving
system.
WARNING! Use on a level and solid surface such as concrete.
8 DO NOT use the corner moving system for any purpose other than that for which it is designed.
8 DO NOT overload the corner movers, 37.5 kgs per corner mover.
8 DO NOT let go of the load whilst in motion.
9 Keep the general area where used clean, uncluttered and ensure there is adequate lighting.
9 Ensure that the corner movers are properly assembled before loading.
9 We recommend two operators for heavier loads.
9 Always push the loaded corner movers as near to bottom of the load as sensibly practical to avoid tipping hazard.
9 Always use all 4 corner movers to transport the load.
2. INTRODUCTION
Heavy-duty corner dollies manufactured from high quality steel with a maximum load weight of 150kg. Ideal for moving awkward rectangular
loads and provides increased mobility in locations where normal material handling equipment cannot be used. Each corner dolly is tted with
three free moving castor wheels for easy manoeuvrability and tted with a rubber covered load area to help secure loads. Ideal for moving
items such as cabinets, desks and much more. Sold in sets of four.
3. SPECIFICATION
Model No.: ..................................................................... CM4
Capacity ....................................................................... 150kg
4. ASSEMBLY
4.1. Place the 12 plain washers on to the 12 castor studs (fig.1).
4.2. Wind the castor studs into the 3 captive nuts in the corner platforms (fig.2). Ensure the castors are tight using “plumbers” pliers or
similar thin nosed grips on to the swivel ball race outer journal (fig.1).
4.3. Position the rubber pads as in fig.3.
Original Language Version
© Jack Sealey Limited
Refer to
instructions
g.1
g.2
g.3
Wear safety
footwear
CM4 Issue 2 (H,F) 26/02/20
Question and Answer IconNeed help?

Do you have a question about the Sealey CM4 and is the answer not in the manual?

Summary

Safety Precautions

Safety Instructions and Warnings

Adherence to safety regulations, proper use, load limits, and operational precautions for safe handling.

Product Introduction

Product Specifications

Assembly Instructions

Washer Placement

Place plain washers onto the castor studs before assembly.

Castor Stud Installation

Install castor studs into captive nuts and ensure they are tight.

Rubber Pad Placement

Position the rubber pads on the corner platforms as shown.

Operating Instructions

Maneuvering Loads

Maneuver loads by pivoting and rolling the corner platforms beneath them.

Load Removal and Securing

Remove loads and steady the corner platforms, using feet for support.

Maintenance Guide

Castor Integrity Check

Regularly check the integrity of the swivel castors.

Cleaning Instructions

Clean the unit with a moistened cloth and mild detergent.

Ball Journal Lubrication

Apply grease to ball journals if required for smooth operation.

Summary

Safety Precautions

Safety Instructions and Warnings

Adherence to safety regulations, proper use, load limits, and operational precautions for safe handling.

Product Introduction

Product Specifications

Assembly Instructions

Washer Placement

Place plain washers onto the castor studs before assembly.

Castor Stud Installation

Install castor studs into captive nuts and ensure they are tight.

Rubber Pad Placement

Position the rubber pads on the corner platforms as shown.

Operating Instructions

Maneuvering Loads

Maneuver loads by pivoting and rolling the corner platforms beneath them.

Load Removal and Securing

Remove loads and steady the corner platforms, using feet for support.

Maintenance Guide

Castor Integrity Check

Regularly check the integrity of the swivel castors.

Cleaning Instructions

Clean the unit with a moistened cloth and mild detergent.

Ball Journal Lubrication

Apply grease to ball journals if required for smooth operation.

Overview

  1. Function Description
  2. Important Technical Specifications
  3. Usage Features
  4. Maintenance Features

The Sealey CM4 Set of 4 Corner Transport Dollies are heavy-duty devices designed to facilitate the movement of awkward rectangular loads, particularly in locations where traditional material handling equipment might be impractical. Manufactured from high-quality steel, these dollies offer increased mobility and a robust solution for transporting items such as cabinets, desks, and other similar objects. They are sold in sets of four, providing a complete system for handling large items.

Function Description:

The primary function of the Sealey CM4 dollies is to allow for the safe and efficient movement of heavy and bulky rectangular loads. Each dolly is designed to fit under one corner of an object, effectively lifting it slightly off the ground and placing it on wheels. This setup enables a single operator (or two for heavier/taller loads) to pivot and roll the load with relative ease. The dollies are particularly useful for navigating tight spaces or areas with limited maneuverability, where forklifts or pallet jacks might not be suitable. The rubber-covered load area on each dolly helps to secure the load, preventing slippage during transport.

Important Technical Specifications:

  • Model No.: CM4
  • Capacity: 150kg per set (meaning 37.5 kg per corner mover, as stated in the safety warnings).
  • Construction: Manufactured from high-quality steel, ensuring durability and strength.
  • Wheels: Each corner dolly is fitted with three free-moving castor wheels, which provide 360-degree maneuverability. These castors are designed for smooth movement across level, solid surfaces like concrete.
  • Load Area: Features a rubber-covered load area to enhance grip and secure the item being moved.

Usage Features:

  • Assembly: The dollies require minimal assembly. Users need to place 12 plain washers onto the 12 castor studs and then wind the castor studs into the 3 captive nuts in the corner platforms. It is crucial to ensure the castors are tightened securely using appropriate tools like "plumbers" pliers or thin-nosed grips. Finally, the self-adhesive rubber pads need to be positioned correctly on the platforms.
  • Operation:
    • Placement: To use, the load is pivoted, and the wheeled corner platforms are rolled beneath each corner of the object. For heavier or taller loads, two operators are recommended. The dollies should be nested fully under the load.
    • Movement: Once all four dollies are in place, the load can be pushed. It is advised to push the loaded corner movers as close to the bottom of the load as practically possible to minimize the risk of tipping. All four corner movers must be used to transport the load.
    • Removal: Removal is the reverse of loading; the corner platforms are steadied with the feet as the load is removed.
  • Safety Precautions:
    • Always adhere to Health & Safety and local authority regulations.
    • Use only on a level and solid surface, such as concrete.
    • Do not use the system for any purpose other than its intended design.
    • Never overload the dollies (maximum 37.5 kg per corner mover).
    • Do not let go of the load while in motion.
    • Keep the work area clean, uncluttered, and well-lit.
    • Ensure dollies are properly assembled before loading.
    • Two operators are recommended for heavier loads.
    • Always push near the bottom of the load to prevent tipping.
    • Always use all four corner movers.

Maintenance Features:

  • Regular Checks: The integrity of the swivel castors should be checked regularly, ensuring they remain tight and functional.
  • Cleaning: The dollies should be kept clean using a moistened cloth and mild detergent.
  • Lubrication: If required, the ball journals of the castors should be smeared with grease to ensure smooth operation and longevity.

The Sealey CM4 dollies are designed for durability and ease of use, providing a practical solution for moving large, heavy, and awkward items in various settings, from workshops to offices. Proper assembly, adherence to safety guidelines, and routine maintenance will ensure years of trouble-free performance.

Sealey CM4 Specifications

General IconGeneral
BrandSealey
ModelCM4
CategoryOutdoor Cart
LanguageEnglish

Related product manuals